Toho Electronics TTM-300 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 24

Toho Electronics TTM-300 Series Скачать руководство пользователя страница 6

5

3.2 Example of Wiring:

In case of the Heating Furnace with voltage of 85

～

265V AC, Thermocouple Input and Relay Contact Output.

85

～

264V AC

Power Source
TTM-300 magnet Heating Furnace

                                        Relay Contact                                                                                                  Heater
                                                                NC
                                                C
                                                                NO

Output Signal Line
Load line

Thermocouple

Input Signal Line

3.3 CAUTION AT WIRING CONNECTION

WARNING

・

For prevention of electric shock, please do wiring connection only after turning off Power.

CAUTION

・

This unit does not function for approx. 4 seconds after turning on Power.

(No function at Output side)
Please be cautious when this unit is used as Interlock circuit.

・

For prevention of miswiring, please make sure to confirm the name labels i.e. Input terminal

Power source terminal and Option terminals etc. beside the each wire.

・

The crimp terminals for wiring should be fit with the nuts of M3.5. As for the wiring to center terminal, use the

lead-wire and fasten on it.

・

The wiring material to connect R.T.D. and this unit should be used the one having wire resistance less than 5

Ω

per

wire.

・

The wiring material to connect Thermocouple and this unit should be used the specified extension leadwire of

thermocouple or leadwire itself.

・

In case this unit should be used close to the noise generators, please use shield-wires.

Please do not wire the Input/Output lines inside of the same duct and the pipes of electric wires.

・

The signal wire of Input/Output should be away from power supply and loaded lines at least 50cm.

«
...
4
5
6
7
8
...
»

Содержание TTM-300 Series

























Отзывы:

Нет отзывов