manualshive.com logo in svg

Tohnichi R-CM, Руководство по эксплуатации

Поделиться
Скачать
Tohnichi R-CM Скачать руководство пользователя страница 5

Modular Conversion Receiver Model: R-CM

　5

3

External View and Each Part Name

3-1. Figure and Name of Parts for T-FH/T-FHM and previous transmitters

Front Cover

Module Fixing Lever

Status Lamp

Receive LED

In/Output Terminal Locker

Power Terminal

SET button

SELECT button

LCD

RS232C Connector

Power Switch

Extension Connector

● Module fixing metal fixtures

It is a lever to fix when the wireless module is installed.

● Front cover

Open it when installing the wireless module or wiring the input / output terminal block.

When the cover is opened, there is an instruction sticker of the terminal block number and 
how to install the radio module.
Close the cover during use.

● Status lamp

The lamp is lit blue or red accordingly the status

* The operations depend on the radio module. For details, refer to the instruction manual for each

wireless module.

● RS232C connector

Used when connecting to an external device (PC / PLC, etc.).

Содержание R-CM





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды