Tohnichi CEM100N3X15D-G Скачать руководство пользователя страница 28

Страница: 28 / 32

DIGITAL TORQUE WRENCH “DATA TORK” MODEL

CEM3-G

Battery

• Setting on PC

(1) Install the driver accompanying No.584 USB cable.

(2) Set the communication port and baud rate.

• Setting on CEM3-G

(3) Set "USB" on communication mode setting, and select the baud rate in line with PC setting.

• Communication

(4) Connect No.584 USB cable to CEM3-G and PC.

(5) Start the software on PC.

Note) No.584 USB cable must be connected before starting the software. Otherwise,

communication error may occur.

Note) CEM3-G can be connected to PC on 1-on-1 basis only.

• Data output

After measuring (tightening), press MEM key to output the data to the software.

To output a range of data at one time, refer to 8. (6) on P18.

Battery life

BP-5 battery can be recharged about 500 times depending on conditions before it dies.

When it is old, replace it with a new one (BP-5).

At the delivery condition, BP-5 battery is empty. Make sure to charge it before use.

How to install the battery

(1) Turn the cap clockwise to remove it.

(2) Set the battery in line with the hole as shown below

and slide it in.

(3) Connect the cable.

(4) Push in the battery to the end.

(5) Push in the cable and the connector carefully.

(6) Put the cap back on by turning it counter-clockwise.

Note) Be careful not to pinch the cable and the connector

when putting the cap on.

How to transfer data to software through USB cable

CEM3-G取扱説明書.indd 28

2016/07/14 11:25:23

Содержание CEM100N3X15D-G

































Результаты поиска

Содержание CEM100N3X15D-G

Отзывы:

Бренды по названию

Популярные бренды

Tohnichi CEM100N3X15D-G, Руководство по эксплуатации

Результаты поиска

Содержание CEM100N3X15D-G

Отзывы:

Бренды по названию

Популярные бренды