TOHATSU MD 30B2 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 92

background image

32

INSTALLATION

4

Incorrect or unstable installation of the Drag Link Assembly can result in accidents
while riding the boat or breakage of the hull.
Installation of the Drag Link Assembly by your dealer is highly recommended.

①

Connect the Drag Link Rod to the tip of the steering cable.

Tighten the rod using self-locking nut, making sure the rod can swing freely.

②

Connect the other tip of the rod to the steering bracket with a bolt, applying a
collar and washer. The bolt head must face downward. Secure with a split pin
to the bolt.

5. Installing the drag link assembly

Note

Depending on the steering cable
manufacturer, spacers (optional) may
by required.

Note

Apply grease in required
places.(Refer to the illustration below)
Apply grease inside the bracket bolt.

Grease

Grease

Steering bracket

Seal ring

Washer

Rod

Bolt

Collar

Collar

Spacer

(optional)

Split pin

Apply grease inside

the Bracket bolt

30

・

40 · 50

Apply grease on tip

of Steering cable

Washer

Self

locking

type nut

75

・

90

・

115

Apply grease inside

the Bracket bolt

Grease

Grease

Tip of cable

Seal ring

Washer

Washer

Washer

Nut with nylon-stopper

Drag link rod

Bolt

Collar

Nut

Spacer

(optional)

Steering bracket

OM_E_MD30B2-115A2_body_111213.indd 32

11/12/13 13:07

«
...
30
31
32
33
34
...
»

Содержание MD 30B2





























































































Отзывы:

Нет отзывов

Похожие инструкции для MD 30B2

Бренд: O.S. engine Страницы: 21

Бренд: Atlas Copco Страницы: 156

Бренд: Scania Страницы: 83

Бренд: Sachs Страницы: 42

EM-PMI540-T1500

Бренд: Danfoss Страницы: 76

Бренд: Louvolite Страницы: 4

Бренд: Yanmar Страницы: 84

Бренд: Yanmar Страницы: 20

Бренд: Yanmar Страницы: 50

Бренд: Yanmar Страницы: 50

Бренд: Yanmar Страницы: 65

Бренд: Yanmar Страницы: 70

Бренд: KTM Страницы: 59

Бренд: A'OK Страницы: 6

DESMO TWINCAM 4V

Бренд: Takegawa Страницы: 19

Бренд: Odyssey Страницы: 14

Бренд: Saito Страницы: 22

Бренд: CAME Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды