manualshive.com logo in svg

TOHATSU MD 25B2 JET, Руководство пользователя

Поделиться
Скачать
TOHATSU MD 25B2 JET Скачать руководство пользователя страница 7

4

5

How the Jet Drive Operates

A  jet  driven  boat  has  substantially  different  handling  characteristics  compared  to  a  propeller 
driven boat. It is recommended that the operator adjusts to these characteristics by experimenting 
in open water at both high and low speeds. The driveshaft driven impeller draws water up through 
the water intake and then redirects it at a high pressure through the water outlet nozzle to create 
forward thrust. To obtain reverse, the reverse gate moves over the outlet nozzle to direct the water 
in the opposite direction.

a

c

b

a - Water intake
b - Water outlet nozzle
c - Reverse gate

When the jet drive is in neutral, the impeller continues to rotate. However, the reverse gate is 
positioned so that some of the forward thrust is diverted to create reverse thrust. This approximate 
balancing of forward and reverse thrust will minimize any boat movement. Because the impeller 
is always rotating and creating thrust when the engine is running, the boat may tend to move 
slowly forward or backward. This is normal for a direct-drive jet driven boat. The operator should 
be aware of this and use caution whenever the engine is running.

OPERATION

M25 Jet Drive

MD25-35Jet_Owners_Sup_120216.indd   5

12/02/17   19:51

Содержание MD 25B2 JET





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды