manualshive.com logo in svg

TOHATSU MD 25B2 JET, Руководство пользователя

Поделиться
Скачать
TOHATSU MD 25B2 JET Скачать руководство пользователя страница 25

22

23

BOATS WITH A FLAT BOTTOM HULL

  1. 

Place (center) the outboard on the boat transom. 

Set the height of the outboard on the boat transom so that the front edge of the water intake 
housing is in line with the bottom of the boat as shown. Fasten outboard to the transom at this 
height.

Water Testing

CHECKING FOR CAVITATION

The initial outboard height setting should be close to the optimum setting for the outboard. 
However, because of the hull design of some boats, obstructions, or imperfections in the hull 
ahead of the water intake, adjustments may be required to prevent cavitation at running speeds.
When operating the boat, the outboard driveshaft housing should be vertical, or tilted toward 
the boat, when planing to provide a scooping angle on the water intake. Tilting the outboard 
out  beyond  a  vertical  position  reduces  the  scoop  angle  and  can  cause  impeller  slippage  and 
cavitation.

 IMPORTANT 

 :  

If the angle of the boat transom does not allow the driveshaft housing 
to  be  positioned  vertical,  a  wedge  kit  should  be  installed  behind  the 
transom brackets to increase the tilt-in angle.

 NOTE  :  

Slight  cavitation  in  sharp  turns  and  rough  water  is  acceptable,  but 
excessive  cavitation  is  harmful  to  the  outboard  and  should  be  avoided. 
Test run the boat. If cavitation occurs (air enters the pump), the first thing to try 
is lowering the outboard mounting height.

M25 Jet Drive

MD25-35Jet_Owners_Sup_120216.indd   23

12/02/17   19:51

Содержание MD 25B2 JET





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды