Главная
/
TOHATSU
/
BFT 2000A
/
Руководство пользователя

TOHATSU BFT 2000A, Руководство пользователя

Поделиться

Страница: 111 / 126

background image

108

15. TROUBLESHOOTING

WARNING SYSTEM COMES ON

SYMPTOM

POSSIBLE CAUSE

REMEDY

Overheat warning system comes on:

• Overheat indicator comes on.
• Overheat warning buzzer sounds.
• Engine speed decreases and stops at last.
• Engine speed cannot be increased by opening the throttle.
• Engine will stop in 20 seconds after engine speed is limited.

Cooling water intake port clogged.

Clean the cooling water intake port.

Spark plugs have improper heat range.

Replace the spark plugs (see page 86).

• Faulty water pump.
• Thermostat clogged.
• Faulty thermostat.
• Cooling water passage clogged.
• Exhaust gas invades cooling system.

Consult with your outboard motor
dealer.

Oil pressure warning system comes on:

• Oil pressure indicator does not come on.
• Oil pressure warning buzzer sounds.
• Engine speed decreases.
• Engine speed cannot be increased by opening the throttle.

Shortage of engine oil

Add engine oil to the specified level
(see page 41).

Improper engine oil is used.

Change the engine oil
(see page 84).

«
...
109
110
111
112
113
...
»

Содержание BFT 2000A































































































































Отзывы:

Нет отзывов

Похожие инструкции для BFT 2000A

Бренд: IBASE Technology Страницы: 92

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

NORA-W10 Series

Бренд: Ublox Страницы: 22

Бренд: austriamicrosystems Страницы: 19

Бренд: Linear Страницы: 16

Бренд: ASROCK Страницы: 43

Бренд: Gigabyte Страницы: 38

Бренд: Apex Digital Страницы: 5

Бренд: MSI Страницы: 76

ACT2861EVK1-201

Бренд: Active-semi Страницы: 19

Бренд: SOYO Страницы: 99

Бренд: ST Страницы: 18

STEVAL-IPE005V1

Бренд: ST Страницы: 21

Бренд: ST Страницы: 66

Бренд: ST Страницы: 59

Бренд: ST Страницы: 65

Бренд: ST Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды