background image

26

 

Do not expose the charger to moisture such as water, rain or snow while charging the battery pack. 

 

Make sure that condensation is not formed on the charger. When you move the charger from a cold place 
to a warm place, condensation may occur on the outside and inside of the device. In this case, do not operate 
the charger until condensation disappears. Dry the moisture of the device before use.   

Do not forcibly the power cable when disconnecting the charger from the socket. 

 

When the plug attached to a power cable, charging cable, or cable is damaged, immediately stop using the 
charger and replace the damaged parts through Todo works or an authorized professional dealer.

 

Do not give a shock to the charger, use a damaged charger, or disassemble the charger in any manner. The 
damaged charger needs to be replaced or exchanged by Todo works or an authorized professional dealer.   

 

Do not allow children to use the charger. 

 

This charger is designed to operate only on 110 to 220 V. 

Make sure that the plug is properly inserted in the socket before charging.

 

Do not touch the main plug or the charging cable plug with wet hands. 

If the charger plug or main plug is wet or dirty, wipe it with a dry cloth before use.

 

3.4.6. Safety Instructions for a Battery Pack 

 

When using Todo Drive for the first time, charge the battery pack fully in advance.   

 

Do not charge the battery pack at low temperatures below 0

  or at high temperatures above 50

.   

 

Protect the battery pack from heat. For instance, do not expose the battery to strong sunlight for a long 
period of time or keep the battery in a hot car in the sun. 

 

Be careful to avoid a short (short-circuit) of a battery. It is not likely to occur, but if the battery pack is on 
fire, be sure that the battery should not contact water or other liquids. The only extinguishing agent 
recommended by the cell manufacturer is sand. 

 

Todo Drive uses power in all modes. Therefore, make sure to charge the battery pack fully after use.   

Based on the safety and CE approval, no modifications are allowed to the battery pack. Do not open the 
battery pack. Improper open or intentional destruction can result in serious injuries, and in this case, you 
cannot claim for free repair service of the battery.     

 

Protect the battery pack socket from contacting metal materials. Do not keep the battery pack around any 
metal surface or metal objects (for example, screws, paper clips). 

Never put the battery pack in water. 

 

If the battery pack is damaged or defective, it should be checked. And in this case, do not use Todo Drive. 
For return and repair procedures, please contact your dealer (See the Chapter 3.9).       

 

Always keep the battery pack clean and dry. 

Содержание Drive TDV-V2.1












































Отзывы: