1. Unplug the Power Cord, and turn the
Lighted Switch to the “OFF” position.
2. Remove the Water Tank; turn it upside
down, and unscrew the Valve Cap
(SEE FIG.5)
3. Fill the Water Tank with cool water, and
replace the Valve Cap.
4. Place the Water Tank on the Main Unit
(SEE FIG.6). You should hear water flowing
into the Main Unit for a short time.
CAUTION:
Do not operate TOB
i
™
with a dry
Water Tank. When operating, if you want to add water,
first turn the Lighted Switch to “OFF” position, before
removing the Water Tank to avoid burning yourself.
5. Plug TOB
i
™
into a grounded three-pronged outlet.
Warning:
If a grounded three-pronged outlet is not
available, a 3-to-2 prong adapter can be used only
if the adapter itself is properly grounded.
6. Turn the Lighted Switch to “ON” position, the light
will be illuminated.
7. Steam should start flowing from the Steam Nozzle.
Wait for steam to heat sufficiently otherwise you will
create wet spots. Wait at least 30 seconds.
8. To steam a garment, place item of clothing on the hanger and steam directly on
the Hanger Hook.
Caution:
Be careful when handling garments on the Clothes Hanger Hook.
Pulling on the garment with too much force may cause TOB
i
™
to tip.
9. Grasp the handle, and place the Steam Nozzle at the top of the garment. Steam
will rise along the inside and outside of the fabric, removing wrinkles. Slowly
slide the Steam Nozzle vertically, from the top to the bottom of the garment.
You may also reverse this motion and steam from the bottom to the top.
Note: Do not allow kinks to form in the hose at any time.
I N S T R U C T I O N M A N U A L
09
I N S T R U C T I O N M A N U A L
08
Operating Instructions:
Fig. 5
10. Repeat steps 9 until the fabric is wrinkle free.
11. Curtains and draperies can be steamed while they are hanging. Press the
Release Button and use Shoulder Strap to put the Main Unit on the shoulder
for these items.
Note:
1. During steaming, make sure that the hose is fully extended to insure
a free flow of steam through it.
2. When removing the Main Unit from the Base, always use Shoulder Strap.
Assemble the Shoulder Strap on the Main Unit, by inserting the end of
the Shoulder Strap into the slot of the Main Unit. To remove the Shoulder
Strap press the round bump to release the Shoulder Strap.
12. When finished using TOB
i
™
, turn the Lighted Switch to the “OFF” position.
How to Steam
TOB
i
™
removes wrinkles from all your clothes five times faster than iron. It works
on virtually all fabrics, silk, denim, cotton, polyester and wool. PLEASE REFER TO
LABEL ON ITEM OF CLOTHING TO CHECK IF GARMENT CAN BE STEAMED.
SOME FABRICS LIKE LEATHER, SUEDE, VELVET MAY NOT BE SUITABLE FOR
STEAMING. IF YOU ARE NOT SURE THEN STEAM A SMALL PART OF THE
INSIDE OF THE GARMENT TO TEST THAT IT DOES NOT DAMAGE THE FABRIC
BEFORE STEAMING THE ENTIRE GARMENT OR FABRIC.
❖
Some articles can be steamed better from the underside. This allows the
steam to relax the fibers of the material, thus removing the wrinkles.
❖
Pants may be easily steamed by holding them by the cuff.
❖
When steaming, touch material lightly with Steam Nozzle and move up and
down to remove wrinkles. It is important that Steam Nozzle makes contact with
the garment and/or fabric.
❖
Always steam with hose in upright position so any condensation is free to flow
back into the steamer. If steaming in a low position near floor, frequently
extend Hose up and out to keep clear.
❖
TOB
i
™
helps to eliminate trips to the drycleaner by helping to reduce odors. It
will not remove stains from garments.
❖
Convenient hanger/hook mechanism holds both the clothes and steam
head securely.
Fig. 6
