Frequency Response:
+0dB, -3dB. 15Hz~ 30kHz (Measurement of B&K Type 2010 output imp. 5
Total Harmonic Distortion:
0.1%, +4dBm at 1kHz
Ham and Noise (Rg = 150 ohms):
—130dBm Equivalent Input Noise (20Hz~ 20kHz)
—132dBm Equivalent Input Noise (IHF A Weighted)
—88dBm ALL FADERS DOWN (IHF A Weighted)
—73dBm PGM FADER AT NOMINAL AND ALL INPUT FADERS DOWN
(IHF A Weighted)
—63dBm (67dB S/N) PGM FADER AND ONE INPUT FADER AT NOMINAL
(IHF A Weighted)
Maximum Voltage Gain (Input Trim at "0" position):
PROGRAM 88dB: INPUT to PGM OUT
LINE 88dB: INPUT to LINE OUT
REC OUT 74dB: INPUT to REC OUT
AUX IN 44dB: AUX IN to PGM OUT
Equalization:
63Hz ± l0dB Peaking 250Hz ± l0dB Peaking 1kHz ± l0dB Peaking
2kHz ± l0dB Peaking 8kHz ± l0dB Peaking
High Pass Filter:
—6 dB/OCT roll-off below 50Hz at —3dB points
Low Pass Filter:
—6 dB/OCT roll-off above 15kHz at —3dB points
Peak Indicators:
Red LED on each input channel
LED's turn on at l0dB below clipping
Channel ON/OFF Indicators:
Green LED on each input channel
Phantom Power:
Phantom powering (48V DC) switch on each input channel
Dimension:
17.99(W) X 15.65(D) X 6.22(H) inch 457(W) X 397.5(D) X 158(H)mm
INPUT SPECIFICATIONS
CONNEC-
TION
INPUT
(1-8)
AUX
INPUT
SELECTOR
MIC
LINE
ACTUAL LOAD
IMPEDANCE
FOR USE WITH
NOMINAL
50 TO
MICROPHONES
OR
LINES
OR LOWER
IMP. LINES
OR LOWER
IMP. LINES
TRIM
POSITION
0
—30
0
—30
SENSITIVITY
(AT MAX GAIN)
—84dBm (0.049mV)
—54dBm (1.55mV)
—44dBm (4.9mV)
—14dBm (155mV)
—40dBm (7.75mV)
INPUT LEVEL
NOMINAL
—64dBm (0.49mV)
—34dBm (15.5mV)
—24dBm (49mV)
+ 6dBm (1.55V)
—20dBm (77.5mV)
*MAX. BEFORE
CLIP
—35dBm (13.8mV)
—5dBm (436mV)
+ 5dBm (1.38V)
+ 36dBm (48.9V)
+ 9dBm (2.18V)
CONNECTOR
XLR TYPE
XLR-3-31
PHONE JACK
CONNECTION
PROGRAM OUT
LINE OUT
REC OUT
(HEAD) PHONES
FOR USE WITH NOMINAL
OR HIGHER IMP. LINES
OR HIGHER IMP. LINES
OR HIGHER IMP. LINES
OUTPUT LEVEL
NOMINAL
+ 4dBm (1.23V)
+ 4dBm (1.23V)
—10dBm (245mV)
—10dBm (245mV)
MAX. BEFORE CLIP
+ 25dBm (13.8V)
+ 25dBm (13.8V)
+ 10dBm (2.45V)
—5dBm (436mV)
CONNECTOR
XLR TYPE
XLR-3-32
PHONE JACK
PHONE JACK
*0dBm is referenced to 0.775VRMS
*Sensitivity is the lowest level that will produce an output of +4dBm (1.23V), or the nominal input level when the unit
is set to maximum gain.
*All XLR type connectors are floating ("balanced") and transformer-isolated. Phone jacks are unbalanced (except
head phone jack, wird Tip = Hot, Ring = Hot, Sleeve = Common)
OUTPUT SPECIFICATIONS
– 11 –
Specifications
All manuals and user guides at all-guides.com