Specifications
–130dBm (20Hz ~ 20kHz)
–133dBm (IHF A)
–102dBm (IHF A)
–93dBm (IHF A)
–72dBm (IHF A)
Frequency Response
+0, -3dB 30Hz~20kHz (HIGH Zinput TRIM at "0" position.)
Equalization
63Hz ±12dB Peaking
125Hz ±12dB Peaking
12dB Peaking
500Hz ±12dB Peaking
1kHz +12dB Peaking
2kHz ±12dB Peaking
4kHz ±12dB Peaking
8kHz ±12dB Peaking
16kHz ±12dB Peaking
Peak Indicators
Red LED on each input channel LED's turn on at 3dB below
clipping.
INPUT SPECIFICATIONS
CONNECTION
CH1
CH6
AUX (1~2)
EFF/RET
GEQ
PWR/AMP
INPUT
LOW Z
HIGH Z
——
——
——
——
ACTUAL
LOAD
IMPEDANCE
OPEN
50k
10k
50k
50k
10k
FOR USE
WITH
NOMINAL
50 TO 250
MICRO-
PHONES
50k OR
LOWER IMP
LINES
10k OR
LOWER IMP,
LINES
50k OR
LOWER IMP,
LINES
50k OR
LOWER IMP,
LINES
10k OR
LOWER IMP
TRIM
POSI-
TION
10
0
10
0
SENSITIVITY
(PGM OUTPUT
LEVEL +4dBm)
-55dBm (1.38mV)
-16dBm (123mV)
-35dBm (13.8mV)
+4dBm (1.23V)
-20dBm (77.5mV]
-20dBm (77.5mV]
+4dBm (1.23V)
+4dBm (1.23V)
MAX BEFORE
CLIP INPUT
LEVEL
-34dBm (15mV)
+1.7dBm (0.94V)
-14dBm (150mV)
+20dBm (7.75V)
-2dBm (0.61V)
-2dBm (0.61V)
CONNECTOR
XLR TYPE NC3F
PHONE JACK
PHONE JACK
PHONE JACK
PHONE JACK
PHONE JACK
OUTPUT SPECIFICATIONS
CONNECTION
PGM
EFF
GEQ
FB
REC
ACTUAL LOAD
IMPEDANCE
600
600
600
600
1k
FOR USE WITH
NOMINAL
600 OR HIGHER
IMP. LINES
600 OR HIGHER
IMP. LINES
600 OR HIGHER
IMP. LINES
600 OR HIGHER
IMP. LINES
1k OR HIGHER
IMP. LINES
OUTPUT LEVEL
NOMINAL
+4dBm (1.23V)
-10dBm(245mV)
+4dBm (1.23V)
+4dBm (1.23V)
-10dBm (245mV)
MAX. BEFORE
CLIP
+20dBm (7.75V)
+8dBm (1.9V)
+20dBm (7.75V)
+20dBm (7.75V)
+8dBm (1.9V)
CONNECTOR
PHONE JACK
PHONE JACK
PHONE JACK
PHONE JACK
PHONE JACK
POWER AMPLIFIER SECTION
Frequency Response
+0, -1dB 5Hz to 40kHz (200W RMS 4 )
Rated Power & Load
300W RMS (2 ) 200W RMS (4 ) 120W RMS (8 )
Power Output at Clipping
1% THD, 1kHz
348W RMS (2 ) 238W RMS (4 ) 140W RMS (8 )
Total Harmonic Distortion
Less than 0.1% (200mW~200W RMS, 20Hz~20kHz)
Typically below 0.05%
Compresser Dynamic Range
Greater than 26dB
Hum and
Noise
At least 110dB S/N ratio, 20Hz~20kHz
At least 113dB S/N ratio IHF-A weighted
Damping Factor
Greater than 200 (1kHz 4 )
Input Sensitivity
+4dBm (1.23V)
Input Impedance
10k
Output Connector
Phone Jack×2
Power Requirement
600 W 120V AC 50/60Hz
Dimensions
585(W)×333(H)×302(D) (23.03×13.11×11.89) inch
Weight
20.3 kg (44.75 lbs)
*0dBrn is referenced to 0.775V RMS.
*
Specifications are subject to change without notice.
MIXER SECTION
Total Harmonic Distortion
0.05% +4dBm at 1kHz.
Hum and
Noise
(Open)
Equivalent Input Noise
Equivalent Input Noise
All level Controls Minimum
PGM Master at MAX and all
input level controls minimum
PGM Master at MAX and one
input level control at MAX
Maximum Voltage Gain
INPUT to PGM out
INPUT to EFF out
INPUT to FB out
INPUT to REC out
INPUT to GEQ out
AUX to PGM out
EFF/RET to PGM out
59dB
45dB
59dB
45dB
59dB
24dB
24dB
- 9 -
All manuals and user guides at all-guides.com
