TMC TI7NBF Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 79

background image

Chapter 5 Installation

24

TI7NBF Socket 370 ATX Motherboard User’s Manual

SMI/Hardware Switch: Pins 6 and 16

This connector supports the "Green Switch" on the control
panel, which, when pressed, will force the system board into
the power-saving mode immediately.

Pin #

Signal Name

6 Sleep

16 Ground

ATX Power ON Switch: Pins 7 and 17

This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the motherboard that connects to the power
switch on the case. When pressed, the power switch will
force the motherboard to power on. When pressed again, it
will force the motherboard to power off.

Turbo LED Connector: Pins 8 and 18

There is no turbo/deturbo function on the motherboard. The
Turbo LED on the control panel will always be On when
attached to this connector.

Pin #

Signal Name

8 5V

18 Ground

Reset Switch: Pins 9 and 19

The reset switch allows the user to reset the system without
turning the main power switch Off and then On. Orientation
is not required when making a connection to this header.

«
...
28
29
30
31
32
...
»

Содержание TI7NBF
















































































Отзывы:

Нет отзывов

Похожие инструкции для TI7NBF

Бренд: Lantronix Страницы: 8

Cyclone IV GX FPGA

Бренд: Altera Страницы: 60

Бренд: Alcad Страницы: 98

Бренд: LITETRONICS Страницы: 2

Z690 Phantom Gaming 4

Бренд: ASROCK Страницы: 109

Бренд: Biostar Страницы: 85

Бренд: ASROCK Страницы: 198

Бренд: Gigabyte Страницы: 100

Бренд: ECS Страницы: 52

B550 AORUS ELITE AX V2

Бренд: Gigabyte Страницы: 12

Бренд: Telaire Страницы: 4

SERVER SYSTEM SR2500AL

Бренд: Intel Страницы: 210

Бренд: Texas Instruments Страницы: 6

Side-Power SX100/185T

Бренд: SLEIPNER MOTOR AS Страницы: 16

Бренд: Intel Страницы: 87

Бренд: Supero Страницы: 108

Бренд: DFI Страницы: 185

Бренд: Gan Systems Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды