manualshive.com logo in svg

TMC TI6NL, Руководство пользователя

Поделиться
Скачать
TMC TI6NL Скачать руководство пользователя страница 6

Chapter 2  Specifications 

2 

TI6NL User’s Manual 

 

Chapter 2  Specifications 

 
The TI6NL is a high-performance ATX 440LX motherboard with a Slot 
1 connector for Pentium

 II processors. It offers flexibility in terms of 

CPU frequency and main memory type and size. The main features of the 
motherboard consist of the following: 

CPU Socket 

Slot 1  

Processor 

Intel Pentium II 233/266/300/333MHz  

L2 Cache 

CPU integrated L2 cache 

Main Memory 

Four 168-pin DIMM sockets 
Memory types: Extended Data Output (EDO) DRAM, SDRAM 
(Synchronous DRAM)  
Memory size: 8MB, 16MB, 32MB, 64MB, 128MB 

Chipset 

Intel 82440LX with built-in PCI-IDE 

Super I/O 

Onboard super I/O is an Winbond W83977TF that provides: 

z

Two 16550 UART compatible serial ports 

z

One parallel port (ECP/EPP compatible) 

z

One floppy controller (2.88MB compatible) 

z

One IrDA port 

z

Keyboard Controller 

PCI Bus Master IDE Controller (Ultra DMA/33) 

Onboard PCI Bus Master IDE (Ultra DMA/33) controller with two 
connectors for up to four IDE devices in two channels, supporting 
faster data transfer rates, enhanced IDE devices such as Tape Backup 
and CD-ROM drives, PIO Mode 3/4 and Bus Mastering Ultra 
DMA/33 (

You have to install the Bus Master IDE driver to enable this 

feature

.) 

Содержание TI6NL
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды