TMC TI6NL Скачать руководство пользователя страница 52

Страница: 52 / 63

Chapter 6 BIOS Configuration

TI6NL User’s Manual

On-Chip Primary/Secondary PCI IDE

The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select

Enabled

to activate each channel

separately.

USB Keyboard Support

Select

Enabled

if your system contains a Universal Serial Bus (USB)

controller and you have a USB keyboard.

Onboard FDC Controller

Select

Enabled

if your system has a floppy disk controller (FDC)

installed on the system board and you wish to use it. If you install an
add-in FDC or the system has no floppy drive, select Disabled in this
field. This option allows you to select the onboard FDD port.

Onboard Serial/Parallel Port

These fields allow you to select the onboard serial and parallel ports and
their addresses. The default value for these ports are:

Serial Port 1

3F8/IRQ4

Serial Port 2

2F8/IRQ3

Parallel

Port

378H/IRQ7

UART Mode Select

This field determines the UART mode in your computer. The settings are

Normal, IrDA and ASKIR

. The default value is

Normal

Parallel Port Mode

This field allows you to determine parallel port mode function.

SPP

Normal Printer Port

EPP

Enhanced Parallel Port

ECP

Extended Capabilities Port

Содержание TI6NL
































































Результаты поиска

Содержание TI6NL

Отзывы:

Бренды по названию

Популярные бренды

TMC TI6NL, Руководство пользователя

Результаты поиска

Содержание TI6NL

Отзывы:

Бренды по названию

Популярные бренды