background image

 

172-65168MA-04  (SA3)    1  Oct  2021

 

7

 

Maintenance 

 

 

Take measures to prevent people from coming into direct contact with 

product outlets. Failure to do so may result in burns or other injury from 

the discharge of fluids.

 

CAUTION 

 

 

Be sure to use only the recommended components when repairing the 

product, and NEVER attempt to modify the product in any way. Failure to 

observe these precautions may result in damage to the product or burns 

or other injury due to malfunction or the discharge of fluids.

 

CAUTION 

 

Operational Check 

A visual inspection of the following items should be done on a daily basis to 
determine whether the air vent is operating properly or has failed.   
If the air vent should fail, it may cause water leakage or hindrance to water flow. 

Normal                                                 

: Air is discharged as it accumulates, with the air vent 

closing (with no leakage) when no air is present in the 
piping 

Blocked                                         
(Discharge Impossible) 

: No air is discharged though air accumulates in the air 

vent 

Leakage   

: Water is discharged or leaks through the air vent outlet 

during closed position 

Parts Inspection 

When parts have been removed, or during periodic inspections, use the following 
table to inspect the parts and replace any that are found to be defective. 

Procedure 

Body Gasket, O-ring 

: Check for warping and damage 

Valve, Valve Seat 

: Check for scratches or wear 

 

Содержание SA3














Отзывы: