manualshive.com logo in svg

TLV S-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV S-COS-16 Скачать руководство пользователя страница 12

 

172-65260m-05 (S-COS/S-COSR Pressure Reducing Valve)  27 Oct 2008

 

12

9. 

Two-stage Pressure Reduction 
Two-stage pressure reduction should be performed whenever the pressure 
cannot be reduced to the desired level with a single pressure-reducing valve due 
to operating range limitations, such as when the reduction ratio is greater than 
10:1.

 

 

 

 

 

 
 
 
 

Accessories 
Always install a shut-off valve, pressure gauge and bypass line at both inlet and 
outlet. 
Ball valves, which will not retain condensate, are recommended for inlet and 
outlet shut-off valves. The bypass pipe should be at least one half the size of the 
inlet (primary side) pipe. 
A strainer should always be installed ahead of the S-COSR. S-COS has a built-in 
strainer, however in case an external strainer is installed, it should be installed 
ahead of COSPECT and the strainer should be installed horizontally with the 
basket at the 3 or 9 o’clock position in order to prevent condensate accumulation. 

 

 

   

   

Safety Valve 

(Relief Valve) 

Pressure 

Gauge 

Shut-off 

Valve 

Bypass Valve

Shut-off Valve

Primary 

Side 

Secondary 

Side 

Ball Valve 

Shut-off 

Valve 

Bypass Valve 

Shut-off Valve 

Pressure

 

Gauge 

Pressure 

Gauge

Globe Valve 

Pressure 

Gauge 

 

Ball Valve

Содержание S-COS-16

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды