TLV JH8R-B Скачать руководство пользователя страница 11

Страница: 11 / 16

172-65464MA-02 (JH8R-B) 18 Nov 2020

Disassembly/Reassembly of Components inside the Air Vent Case/Guide

Part

During Disassembly

During Reassembly

Snap Ring

Pinch the insides together
and remove from the air vent
case

Insert securely into the groove
in the air vent case

Air Vent Screen

Remove, being careful not to
misshape

Replace, being careful not to
misshape.

Bimetal Unit
(Bimetal Plate /
Snap Ring / Valve
Plug)

Remove the air vent parts
from cover

Make sure to reinsert in the
proper orientation (Fig. A)

Air Vent Valve Seat Remove with a socket

wrench

Consult the table of tightening
torque and tighten to the
proper torque

Air Vent Case

Remove from the cover

Place it in the cover

Air Vent Guide

Remove with a socket
wrench

Consult the table of tightening
torques and tighten to the
proper torque

Air Vent Guide
Gasket

Remove the gasket and
clean sealing surfaces

Replace with a new gasket,
coat with anti-seize

Disassembly/Reassembly of Components Inside the Body

Part

During Disassembly

During Reassembly

Snap Ring

Pinch insides together and remove
from the body

Insert securely into the groove in the
body

Screen

Remove by grasping the wire ring
and lifting straight up and out

Set the screen on the screen holder
and screen holder retainer and insert
as far as the snap ring groove

Screen Holder
Retainer

Remove without bending

Place on the screen holder without
tilting

Screen Holder

Remove without bending

Place on the ledge inside the body,
making sure the rounded side is on
top

Float

Remove, being careful not to scratch
the polished surface

Insert, being careful not to scratch
the polished surface

Outlet Cover Nut

Remove with a socket wrench

Consult the table of tightening
torques and tighten to the proper
torque

Outlet Cover

Remove, being careful not to scratch
the gasket sealing surface

Make sure there are no pieces of the
old gasket left on the sealing
surfaces of the body and cover

Outlet Cover
Gasket

Remove the gasket and clean
sealing surfaces

Replace with a new gasket

Orifice

Remove with a socket wrench

Consult the table of tightening
torques and tighten to the proper
torque

Orifice Gasket

Remove the gasket and clean
sealing surfaces

Replace with a new gasket; coat
surfaces with anti-seize

Figure A

Содержание JH8R-B
















Результаты поиска

Содержание JH8R-B

Отзывы:

Бренды по названию

Популярные бренды

TLV JH8R-B, Инструкция по эксплуатации

Результаты поиска

Содержание JH8R-B

Отзывы:

Бренды по названию

Популярные бренды