TLV CV-COS-20 Скачать руководство пользователя страница 23

Страница: 23 / 30

172-654741MA-01 (CV-COS-20/CV-COS-20D) 7 Oct 2021

Removing/Reattaching the Trap and its Components

Part

During Disassembly

During Reassembly

Bolts for Trap
Cover/Float
Cover Bolt &
Spring
Washers

Remove with a socket wrench

Consult the table of tightening
torques and tighten to the proper
torque

Float Cover

Pull up and off

Replace with a new float cover

Float

Remove, being careful not to
scratch the polished surface

Insert, being careful not to scratch
the polished surface

Trap Valve
Seat

Remove with a socket wrench

Consult the table of tightening
torques and tighten to the proper
torque

Trap Valve
Seat Gasket

Remove the gasket and clean
sealing surfaces

Replace with a new gasket if
warped or damaged

Trap Cover
Gasket

Remove the gasket and clean
sealing surfaces

Replace with a new gasket if
warped or damaged

Trap Cover
Bolt

Float Cover

Bolt

Trap Valve Seat

Float Cover

Float

Trap Cover
Gasket

Float Cover
Bolt

Float

Trap Cover

Spring

Washer

Trap Valve Seat Gasket

Trap Cover

Trap Valve Seat

Gasket

Float Cover

Trap Cover

Baffle

Baffle Nut

Содержание CV-COS-20































Результаты поиска

Содержание CV-COS-20

Отзывы:

Бренды по названию

Популярные бренды

TLV CV-COS-20, Инструкция по эксплуатации

Результаты поиска

Содержание CV-COS-20

Отзывы:

Бренды по названию

Популярные бренды