background image

  

 

 

www.tkequip.com

 

(956) 796 - 9411

 

 

1. SERIAL NUMBER LOCATION 

The model/serial number decal is located on the Frame.

 

 

(Write model number) 

 

(Write serial number) 

The  unit  year  of  manufacturing  can  be  determined  by  its  serial  number.  So,  keep  this 
information handy at all times, use your unit serial number when ordering parts. 

This Unit warranty is stated in this Operational and Safety manual on page 16. Failure to return 
warranty registration card renders the warranty null and void. 

An 

engine owner’s man

ual is also attached to every unit. Engine parts must be order from any 

authorized  HONDA  dealer,  or  other  if  different  than  HONDA.  Refer  to  the  engine  owner´s 
manual lo learn about specifications and part identification. 

2. PARTS ORDERING PROCEDURE:

 

Parts must be ordered through your local distributor or online using our partner internet parts 
dealers. If 

you can’t locate 

a local distributor in your area visit us online at 

www.tkequip.com

 

for information so we can locate the nearest dealer and contact numbers for assistance. 

All Dealers are welcome to send us an email to: 

[email protected]

 or 

[email protected]

 

All Dealers are welcome to order parts via fax by dialing 

(956) 462-2500 

 All Dealers are welcome to order parts by dialing our Number 

(956) 796-9411 

 
All  HONDA  warranties  and  parts  ordering  must  be  through  your  Honda  dealers. 
Please  visit 

https://engines.honda.com/dealer-locator

 

for  more  information. 

 

 

Содержание BBS20






















Отзывы: