background image

9

LIMITED PARTS WARRANTY AND CLAIM PROCEDURE

Tjernlund Products, Inc. warrants the components of its products for one year from date of installation.  This warranty covers defects
in material and workmanship.  This warranty does not cover normal maintenance, transportation or installation charges for replace-
ment parts or any other service calls or repairs.  Products that are tampered with, damaged, or defective due to malfunctioning appli-
ances are not covered under this warranty.  This warranty DOES NOT cover the complete Power Venter if it is operative, except for
the defective part.

Tjernlund Products, Inc. will issue credit to the original distributor or provide a free part to replace one that becomes defective during the
one year warranty period.  If the part is over 18 months old, proof of date of the installation in the form of the contractor sales/installa-
tion receipt is necessary to prove the unit has been in service for under one year.  All receipts should include the date code of the Power
Venter to ensure that the defective component corresponds with the complete unit.  This will help preclude possible credit refusal.

1.) Determine defective component.  If unable to determine faulty component, contact your Tjernlund distributor or Tjernlund Products

Technical Customer Service Department at 1-800-255-4208 for troubleshooting assistance.

2.) After the faulty component is determined, return it to your Tjernlund distributor for replacement.  Please include Power Venter date

code component was taken from.  The date code is located on the Electrical Box cover plate.  If Power Venter date code is older 
than 18 months you will need to provide a copy of the original installation receipt to your distributor.  Credit or replacement will only
be issued to a Tjernlund distributor after the defective part has been returned prepaid to Tjernlund.

COVERED PARTS

Motor

Proving Switch

Relays

Wheel

Housing

WHAT IS NOT COVERED

Product installed contrary to our installation instructions
Product that has been altered, neglected or misused
Product that has been wired incorrectly
Product that has been damaged by a malfunctioning or mistuned burner
Any freight charges related to the return of the defective part
Any labor charges related to evaluating and replacing the defective part

REPLACEMENT PARTS

TJERNLUND LIMITED ONE YEAR WARRANTY

Tjernlund Products, Inc. warrants to the original purchaser of this product that the product will be free from defects due to faulty material or workmanship for a
period of (1) year from the date of original purchase or delivery to the original purchaser, whichever is earlier.  Remedies under this warranty are limited to
repairing or replacing, at our option, any product which shall, within the above stated warranty period, be returned to Tjernlund Products, Inc. at the address
listed below, postage prepaid.  THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, AND TJERNLUND
PRODUCTS, INC. EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF THIS PROD-
UCT.  THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES AND NO AGENT IS AUTHORIZED TO ASSUME FOR US ANY LIABILITY
ADDITIONAL TO THOSE SET FORTH IN THIS LIMITED WARRANTY.  IMPLIED WARRANTIES ARE LIMITED TO THE STATED DURATION OF THIS LIM-
ITED WARRANTY.  Some states do not allow limitation on how long an implied warranty lasts, so that limitation may not apply to you.  In addition, some states
do not allow the exclusion or limitation of incidental or consequential damages, so that above limitation or exclusion may not apply to you.  This warranty gives
you specific legal rights and you may also have other rights which may vary from State to State.  Send all inquiries regarding warranty work to Tjernlund
Products, Inc. 1601 9th Street, White Bear Lake, MN 55110-6794.  Phone (612) 426-2993 • (800) 255-4208 • Fax (612) 426-9547.

MODEL HS-3C

MOTOR KIT

950-1022

WHEEL KIT

950-1013

FAN PROVER KIT

950-1032

HOUSING

950-1014

ISOLATION OR

950-1040 

MOTOR RELAY

Содержание HS-3C CANADIAN 8504002 REV 2 0997











Отзывы: