TitanTec CS6150A Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

8.

Operating the Engine

---------------------------------------------------------------------------------------------------------------

■

ADJUSTING THE CARBURETOR

(1) L needle
(2) H needle
(3) Idle adjusting screw

The  carburetor  on  your  unit  has  been  factory
adjusted,  but  may  require  fine  tuning  due  to  a
change in operating conditions. Before adjusting the
carburetor,  make  sure  that  the  provided  air/fuel
filters  are  clean  and  fresh  and  the  fuel  properly
mixed.
When adjusting, take the following steps:

NOTE

Be sure to adjust the carburetor with the bar chain
attached.

1. H and L needles are restricted within the

number of turn as shown below.

H needle: -1/4 -1/4
L needle: -1/4 -1/4

2.

Start the engine and allow it to warm up in low
speed for a few minutes.

3.

Turn

the

idle

adjusting

screw

(T)

counterclockwise  so  that  the  saw  chain  does
not  turn.  If  the  idling  speed  is  too  slow,  turn
the screw clockwise.

4.

Make a test cut and adjust the H needle for
best cutting power, not for maximum speed.

■

CHAIN BRAKE

This machine is equipped with an automatic brake to
stop saw chain rotation upon occurrence of kickback
during  saw  cutting.  The  brake  is  automatically
operated  by  inertial force, which  acts  on the  weight
fitted inside the front guard.
This  brake  can  also  be  operated  manually  with  the
front guard turned down to the guide bar. To release
the  brake,  pull  up  the  front  guard  toward  the  front
handle till a “click” sound is heard.

WARNING



Be sure to confirm brake operation during daily
inspection.

How to confirm:

1) Turn off the engine.
2) Holding the chain saw horizontally, release your

hand  from  the  front  handle,  hit  the  tip  of  the
guide  bar  to  a  stump or  a  piece  of wood,  and
confirm brake operation. Operating level varies
by bar size.

In  case  the  brake  is  not  effective,  ask  our  dealer  for
inspection and repairs. If the engine keeps rotating at
high  speed  with  the  brake  engaged,  the  clutch  will
overheat  causing  trouble.  When  the  brake  engages
during  operation,  immediately  release  the  throttle
lever to stop the engine.

■

STOPPING THE ENGINE

1

Release the throttle lever to allow the engine to

idle for a few minutes.
2

Set the switch to the “O” (STOP) position.

«
...
13
14
15
16
17
...
»

Содержание CS6150A





















Отзывы:

Нет отзывов

Похожие инструкции для CS6150A

Бренд: McCulloch Страницы: 14

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 32

Бренд: FUXTEC Страницы: 38

Бренд: Echo Страницы: 36

Бренд: Stiga Страницы: 22

Бренд: Stiga Страницы: 39

Бренд: Zenoah Страницы: 60

Бренд: Parkside Страницы: 256

Бренд: Makita Страницы: 21

Бренд: Ikra Страницы: 152

Бренд: stayer Страницы: 40

Бренд: Ryobi Страницы: 92

Бренд: Ryobi Страницы: 120

Бренд: Ryobi Страницы: 120

Бренд: Fieldmann Страницы: 110

Бренд: AL-KO Страницы: 168

Бренд: AL-KO Страницы: 412

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды