background image

 

TITAN Technologies International, Inc.

® 

9001 Jameel Street,  Suite 180 •  Houston, TX 77040 

Toll-Free: 866.345.8484 • Phone: 281.449.9994 • Fax: 281.449.9996 • Email:[email protected]   

http://www.titanti.com 

Safety hints 

 

Apart from observing the general accident prevention regulations, the following 
safety instructions must be observed to prevent life-endangering conditions, 
damage and an increased accident hazard. 

 

If leaks occur when pressure is applied,

 the pressure must be relieved 

immediately. The leak must be sealed and defective components must be 
replaced. 
 

When repairs are made

 use original spare parts only. The unauthorised 

replacement of damaged components with non-original spare parts is not 
permitted. 
 
All components

 must be handled exclusively as described in the 

operating instructions and the general drawing. Changes to the 
functional sequence or a different application are not allowed. 
 

It must always check if the

 high-pressure hoses

 are connected correctly. 

 
The 

high-pressure hoses

 must be laid such that they cannot be driven 

over by vehicles or unnecessarily trodden by persons. Never lay hoses over 
sharp objects (danger of cutting) and do not pinch or trap them. 
 
Before the pressure is applied, the maximum working pressure (without 
consumers) must be adjusted 

by an authorised person 

at the 

pressure-

limiting valve

 (Chap. Pressure adjustment). 

 
The unit is 

not fitted with a safety valve

. The maximum system pressure 

of 2500 bar must never be exceeded. 
 

Repairs

 must only be conducted when the system is depressurised and 

disconnected from the power. 
 
Verify the 

oil level

 before each commissioning. 

 

You must carry protection eyeglasses while working with high-pressure 
hydraulic aggregates. 
 
In the case of use of a remote control, pay attention to electromagnetic 
radiations. 

Содержание WindMaster 2010


















Отзывы: