Titan 759-135, Руководство пользователя

Страница: 5 / 12

© Titan Tool Inc. All rights reserved. 5
1/2" Hex Screw
Large Flat Washer
Panel
Solenoid Valve
Speed Control
Installing the Switch Assembly
Use the following procedure to install the switch assembly onto
the left handle of the PowrLiner.
1. Position the switch assembly against the inside of the left
handle on the PowrLiner directly in front of the handle
grip. Make sure the FORWARD/REVERSE switch on the
switch assembly is positioned so that it can be operated
easily while holding the left handle grip.
2. Place the two clamp plates against the outside of the left
handle so that they line up with the bottom clamps on the
switch assembly.
3. Insert the the two 1” screws through the clamp plates and
into the bottom clamps on the switch assembly. Tighten
securely.
1" Screw
Clamp Plate
FORWARD/REVERSE
Switch
Bottom Clamp
Installing the Hoses
Use the following procedure to connect the hydraulic hoses of
the PowrDrive with the hydraulic system of the PowrLiner.
NOTE: Use an oil pan to catch hydraulic oil that spills
during the removal of the hoses.
1. Remove the high pressure hose from the ball valve on the
motor/pump assembly.
2. Install the 90º street elbow into the ball valve.
3. Install one of the tee fittings into the 90º street elbow.
4. Connect the original high pressure hose to the side outlet
on the tee fitting.
5. Connect the male end of the new 21.5” high pressure
hose to the top outlet on the tee fitting. Run the hose up
along the side of the motor/pump assembly, over the top
of the handle bar panel, and connect the free end of the
hose to the fitting on the top of the solenoid valve.
6. Remove the oil return hose from the elbow on the motor/
pump assembly.
7. Remove the elbow from the motor/pump assembly.
8. Install another tee fitting into the port on the motor/pump
assembly where the elbow was located.
9. Install the original elbow into the side outlet on the tee fitting.
10. Connect the original oil return hose to the original elbow.
11. Connect the male end of the new 37” high pressure hose
to the bottom outlet of the tee fitting. Run the hose down
in front of the motor/pump assembly, underneath the filter
assembly, and up to the 90º elbow at the end of the valve and
speed control assembly. Connect the hose to the 90º elbow.
12. Connect the two new 39.5” high pressure hoses to the
fittings on the bottom of the solenoid valve. Run the hoses
down between the PowrLiner bleed hose and the handle
bar frame, underneath the PowrLiner cart, and toward the
PowrDrive hydraulic drive motor.
13. Connect the hose that runs from the left fitting on the
solenoid valve to the short elbow on the PowrDrive
hydraulic drive motor.
NOTE: Do not use PTFE tape or thread sealant on the
connection at the PowrDrive hydraulic drive motor.
14. Connect the hose that runs from the right fitting on
the solenoid valve to the long elbow on the PowrDrive
hydraulic drive motor.
Tee
PowrDrive 37" Oil
Return Hose
Original Oil
Return Hose
Original Elbow
90º Street
Elbow
PowrDrive 39.5"
High Pressure
Hose
PowrDrive 39.5"
High Pressure
Hose
90º Elbow
Speed Control
Valve
Long Flare
Elbow
Tee
Fitting
Fitting
PowrDrive 21.5"
High Pressure
Hose
Ball Valve
Short Elbow
Hydraulic Drive
Motor
Solenoid
Valve
Original High
Pressure Hose
Motor/Pump
Assembly