background image

General Repair & Service Notes:

WARNING:

Before proceeding, follow the Pressure

Relief Procedure outlined on Page 5.  Additionally,
follow all other warnings to reduce the risk of an
injection injury, injury from moving parts or electric
shock. 

The following tools are needed when repairing this
sprayer:

Phillips Screwdriver

3/8" Allen Wrench

Needle Nose Pliers

5/16" Allen Wrench

Adjustable Wrench

1/4" Allen Wrench

Rubber Mallet

3/16" Allen Wrench

Flat-blade Screwdriver     1/8" Allen Wrench
1/2" Open End Wrench

1. Before repairing any part of the sprayer, read the
instructions carefully, including all warnings.
2. When disconnecting wires, use needle nose pliers to
separate mating connectors.

CAUTION:

Never pull on a wire to disconnect it.

Pulling on a wire could loosen the connector from the
wire.

3. Test your repair before regular operation of the
sprayer to be sure that the problem is corrected.  If the
sprayer does not operate properly, review the repair
procedure to determine if everything was done correctly.
Refer to the Troubleshooting Charts to help identify
other possible problems.
4. Make certain that the service area is well ventilated in
case solvents are used during cleaning.  Always wear
protective eyewear while servicing.  Additional protective
equipment may be required depending on the type of
cleaning solvent.  Always contact the supplier of
solvents for recommendations.
5. If you have any further questions concerning your
TITAN Airless Sprayer, call TITAN:

Customer Service Department 1-800-526-5362

Fax 1-800-528-4826

Outside the U.S. Call 1-201-405-7520

Outside the U.S. Fax 1-201-405-7449 

Canada 1-800-565-8665  

Fax 1-905-856-8496

3

Frame

Add P.S.L. Here

(Piston Seal Lubricant)

Fluid Section

Gas Tank

Pull Start

Syphon Tube

Throttle

NOTE: A Repacking Kit (730-401) is available.  All parts
included in the kits are listed in parts list chart on page 24.
For best results use all parts supplied in the Repacking
Kit.

Air Filter

Bypass Valve

Paint Filter

Gear Box

Figure 1

690HPG

Figure 2

Figure 3

Engine Muffler

Pressure 

Adjustment Knob

Содержание 755-095





















Отзывы: