Titan Pro 15 HP Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 20

Titan Pro 15 HP Скачать руководство пользователя страница 10

10

FUEL & OIL

1. Add unleaded fuel to engine.

1.1. There is

no oil

in the new engine.

1.2. Unscrew the black cover and pull the dipstick out. Use quality oil
with a rating of 15W-40.

Fill to the top of the threads. There is a low oil

cut out in the sump of this machine,

IT WILL NOT START IF THE OIL IS

LOW

1.3. Refer to “starting the engine” for the instructions regarding adding

fuel.

OPERATION

After each use ensure that the cutting chamber and the top and side chutes are
completely clear, run machine until all produce is expelled from the machine



Failure to do this may cause premature belt failure, which is not

covered under warranty.

1.

Make sure the plastic cover on upper hopper is closed when your shredder is

running. Flying chips are very hazardous.

2.

Use a rough wooden stick to push the material in to the feed hopper. Do not

use your hands or metal tools.

3.

Big branches must be fed comparatively slowly into the machine side chute.

4.

Do not allow processed material to build up in the discharge zone; this may

prevent proper discharge and can result in kickback of material through the feed
intake opening and may cause the drum to stop and belt to overheat

«
...
8
9
10
11
12
...
»

Содержание 15 HP





















Отзывы:

Нет отзывов