Time Guard SLFM360 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

Time Guard SLFM360 Скачать руководство пользователя страница 4

3

Parts included

• PIR Sensor unit.
• Instruction manual. Please keep safe for future

reference.

• Accessory Pack. Includes wiring cover, 2 x cable

clamps, 4 x clamp screws and 1 x lens mask sticker.

Tools and parts needed

• 3 core flexible cable.
• Electric/hand-held drill & bits.
• 75mm or 3 inch diameter hole cutter.
• Terminal or Electricians screwdriver.
• Small philips screwdriver.
• Wire cutters.
• Suitable mains interconnect cable.

This product is suitable for indoor use only. Connected
load must not exceed maximum 2000W filament/
incandescent or 500W fluorescent/low energy lighting.
Do not attempt to install if you are suffering from
nausea or dizzy spells or on medication with similar
side effects. If in any doubt, consult a qualified
electrician.

Not suitable for use with discharge lighting.

Selecting a location

The motion detector has a number of detection zones,
at various vertical and horizontal angles as shown (see
diagram A).
A moving human body needs to cross/enter one of
these zones to activate the sensor. The best all-round
coverage is achieved with the unit mounted at the

SLFM360_Instruct_art_2.2.qxd 3/5/06 10:05 am Page 3

«
...
2
3
4
5
6
...
»

Содержание SLFM360













Отзывы:

Нет отзывов