background image

Safety - Basic Safety Rules & Precautions

1.3.5

When transporting the machine, know and use the
signaling devices required by the machine. 
Provide an escort for transporting the machine
when required.

Parking The Machine

When parking the machine, select a spot where the
ground is level.  Do not park on a hillside or an
incline.

When in freezing conditions, planks can be placed
under the machine to prevent the wheels from
freezing into the ground.

Lower grapple to the ground and shut down the
engine.  Remove ignition key and place in
safekeeping.

If the machine is to be parked for a greater length of
time, such as overnight, switch off the master
electrical disconnect or disconnect the positive
(+) battery cable.

Service And Maintenance

Precautions

General

Unless otherwise specified, all maintenance or
repair procedures should begin as follows:

1) Position machine on level ground.
2) Lower grapple to the ground.
3) Shut down engine. Remove ignition key

and place in safekeeping.

4) Switch off master electrical disconnect or

disconnect the positive (+) battery cable.

Run the engine only when it is required for test or
adjustment purposes.s

Form M251

Diesel exhaust fumes contain elements that are
hazardous to your health.  Always run engine in a
well ventilated area.  If in an enclosed space,
vent exhaust to the outside.

00015

Before performing maintenance or repairs on the
machine, consult this manual and follow the
recommended procedures.

00019

Keep your head, hands, and feet  clear of all
moving parts.

00016

Keep yourself, all objects and tools away from
moving fan blades.  Fan blades will cut or throw
any object dropped or pushed into them.  

00020

Содержание TF800





































Отзывы: