manualshive.com logo in svg

THUNDER TIGER Staudacher S-300, Инструкция по сборке

Поделиться
Скачать
THUNDER TIGER Staudacher S-300 Скачать руководство пользователя страница 11

11

ENGINE  & FUEL TANK INSTALLATION

V. Engine Installation

❐

Locate the motor mount hardware: two beams, backplate, two anti-

vibration rubber and four machine screws. Install the adjustable engine
mount. Remember to install anti-vibration rubber to reduce the engine
vibration. Set the engine on engine mount as shown, measure from the
firewall to the front of thrust washer at 13.5cm(5 5/16”). Mark the
engine mounting hole position on the engine mounts.

❐

Drill the engine mounting hole with 3.5mm bit(3/16”) then using

the four 4x24mm Mounting Screws to secure the engine.

❐

Drill a 3mm(1/8”) hole for throttle pushrod guide tube. Install the

pushrod tube and use a couple of drops of medium CA to hold in place
in the firewall.

❐

Install the throttle pushrod. You might need to screw off the throt-

tle lever first then attach to Z-bend throttle pushrod end.

VI. Fuel Tank Assembly

❐

Assemble the fuel tank and install the fuel tank in fuselage.

Содержание Staudacher S-300

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды