THUNDER TIGER Staudacher S-300 Скачать руководство пользователя страница 1

1

ACE  Staudacher-60 ARF Airplane  (TTR4563)

Distributed in North America by Ace Hobby Distributors, Inc. • 2682 Walnut Avenue,Tustin, CA 92780

Phone: 714-544-0330 • www.acehobby.com • email: [email protected]

Assembly Manual

Wing Span:

1650mm 65"

Wing Area:

780  in

2

Length:

1400mm 55.2"

Weight:

3400-3600g 7.5-8 lbs

Engine:

.61 2 Cycle
.91 4 Cycle

Radio:

4 Channel w/5 Servos

Specifications:

Warranty

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.

It does not cover any damage caused by use or modification. The warranty does not extend beyond the
product itself and is limited only to the original cost of the kit. By the act of building this user-assembled
kit, the user accepts all resulting lliability for damage caused by the final product. If the buyer is not 
prepared to accept this liability, it can be returned new and unused to the place of purchase for a refund.

JE6441

Notice: Adult Supervision Required

This is not a toy. Assembly and flying of this product requires adult supervision.

Read through this book completely and become familiar with the assembly and flight of this airplane.

Inspect all parts for completeness and damage. If you encounter any problems, call us for help.

Staudacher S-300

Содержание Staudacher S-300

















Отзывы: