N
PRE-ASSEMBLY NOTES
1. If you are not an experienced R/C pilot plan to have a fully
competent pilot help you to learn to fly your E-Hawk. This
will help you to be successful much faster and also avoid
potential damage to your model.
2. Please assemble your model exactly according to these
instructions. Do not attempt to modify or change the E-Hawk
in any way as doing so may adversely change its flying
characteristics.
3. Before you begin please check the entire contents of this
kit against the parts list and part drawings to be sure that no
parts are missing or damaged. This will also help you to
become familiar with each component of your E-Hawk. If you
find that any of the parts are either missing or damaged
please contact your dealer immediately for replacement.
Note: Your dealer cannot accept kits for return if construction
has begun.
For customers in the US and Canada please call or write to
ACE Hobby Distributors, Inc for replacement of missing or
damaged parts.
ACE Hobby Distributors, Inc.
2055 Main Street, Irvine, CA 92614
Tel: 949.833.0088
Fax: 949.833.0003
E-Mail: [email protected]
Remember. We have worked very hard to make this model
as easy to assemble as possible while still maintaining our
high standards of quality. Your assembly of this model is very
important and will determine the final flight capabilities of
your E-Hawk, so use extra care and follow the assembly
procedure exactly.
OTHER ITEMS REQUIRED
Radio: You will need at least a
2~3 channel radio control system
on an aircraft frequency for use in
your E-Hawk. Recommend ACE
Commander 3ch single stick raido
(P/N ACE 8304) which comes with
2 Micro Servos and Mini Receiver.
However, if you are really looking
for every bit of extra performance
then you should consider using
one of the miniature radio systems
available which would lower the
weight and increase the
performance of your E-Hawk.
Electronic motor controller: We recommend the ACE8007
Auto Cut-Off Device (work with 2CH radio) or ACE8012
ESC-30 with BEC (work with 3CH radio) for controlling the
power of your E-Hawk as well as eliminating the need for a
separate radio battery. The BEC (Battery Eliminator
Circuitry) in this controller will automatically turn off the
power to the motor when the battery reaches a factory
present discharge level leaving about 20-25 minutes of flight
time for the radio system. Note: Some radio manufacturers
offer a lightweight radio system with a built-in motor
controller with BEC especially for this type of model.
Flight Battery: We recommend the use of ACE 2922 7 cell
8.4V 1000 mAh NiMH batter y pack for maximum
performance.
Charger: You will need a battery charger to charge your
power battery. We recommend our ACE2604 8.4V DC Time
Charger for 7-cell bettery pack. Note: When charging your
flight battery be sure to very carefully follow the instructions
provided with the charger.
Extension Wire: 2 servo extensions in 6” long are required.
TOOLS AND SUPPLIES NEEDED
1. 12 Minute Epoxy
2. Thin CA Glue
3. Mixing Stick for Epoxy
4. Medium Grit Sandpaper
5. Rubbing Alcohol
6. Paper Towels
7. Hobby Knife
8. 3/16
Drill
9. 1/16” Drill
10. Ruler
11.
?
?
?
?
?
?
?
?
?W2@6T2@@?
?
?7@X;@@X
?
?@@1?@@1
?
?@@@?@@@
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Z
?
?
?
?
?
?
?
?
@@@?@@@?
?
?@5??@5?
?
?W&(YW&(Y?
?
?&0Y?&0Y
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Bend Pliers
12. Pen, Pencil or Marker
13. Small Screw Drivers
14. Curved scissors
ASSEMBLY INSTRUCTION
ACE 2604
ACE 2922
ACE 8012
ACE 8007
ACE 8304
