background image

17

B

BA

AL

LA

AN

NC

CE

E

Locate A Good Flying Site

Generally, the best place to fly your model is at

an AMA (Academy of Model Aeronautics) chartered
club field. Your local hobby dealer can tell you if
there is such a club in your area or write the AMA
for information.  It is also a good idea to join this
organization before flying your model since they
offer liability insurance that can protect you if
your model causes damage or injury to others.

A

Ac

ca

ad

de

em

my

y  o

off  M

Mo

od

de

ell  A

Ae

erro

on

na

au

uttiic

css

5

5115

511  E

Ea

asstt  M

Me

em

mo

orriia

all  D

DR

R

M

Mu

un

nc

ciie

e,,  IIN

N  4

47

73

30

02

2--9

92

25

52

2

If there is not a chartered club field in your

community, you will need to find a large area free
of obstructions, and has a smooth grass or asphalt
surface to be used as a runway.  For safety’s sake, it
should be located well away from houses,
buildings, schools, power lines and airports.  If you
will be flying within 6 miles of an airport, you
should check with the airport manager before
flying your model.

Congratulations 

Now that you have completed the assembly of

your 3D Spirit, we feel that you have a very capable
and good looking sports plane. We hope that you
will enjoy this model and get many hours of flying
pleasure from its use.  Thank you for purchasing
this 3D Spirit from Thunder Tiger and we look
forward to providing you with other great R/C
products in the future.

Refer to the indicated drawing and box label to stick the decals.

Содержание 3D Spirit





















Отзывы: