background image

A s s e m b l y   M a n u a l

1

Thunder Tiger 3D Spirit ARF Airplane (TTR4572)

Distributed in North America by Ace Hobby Distributors, Inc. • 2055 Main Street, Irvine, CA 92614

Telephone: 949.833.0088 • 

w

ww

ww

w..a

ac

ce

eh

ho

ob

bb

by

y..c

co

om

m  

• E-mail: [email protected]

Wing Span: 53"(1350mm)

Length: 57" ( 1438mm)

Wing Area: 725 sq.in.(  46.8 dm

2

)

Weight: 4.5~5 lbs.(2000~2200g)

Engine: .46~.50 2C

Radio: 4 channel 5 servos req'd

S

Sp

pe

ecciiffiiccaattiio

on

nss::

Warranty

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.  It

does not cover any damage caused by use or modification.  The warranty does not extend beyond the
product itself and is limited only to the original cost of the kit.  By the act of building this user-assembled kit,
the user accepts all resulting in liability for damage caused by the final product.  If the buyer is not prepared
to accept this liability, it can be returned new and unused to the place of purchase for a refund.

Notice:  Adult Supervision Required

This is not a toy.  Assembly and flying of this product requires adult supervision.  

Read through this book completely and become familiar with the assembly and flight of this airplane.

Inspect all parts for completeness and damage.  If you encounter any problems, call us for help.

JE6643

Содержание 3D Spirit





















Отзывы: