background image

MX40G, MX70G Series of E-O Converters

 

Chapter 8: Maintenance, Repair, and Fuses 

Page 34

  

TTN116413-D02 

Chapter 8 

Maintenance, Repair, and Fuses 

8.1  Maintenance and Repair 

The instrument should not need regular maintenance by the user. If necessary the display, housing, and front panel can be 
cleaned using a soft cloth moistened with normal, mild glass cleaner. Do not use any chemical solvents or harsh cleaners on 
the display. Do not spray any cleaning solutions directly onto any part of the unit. 

The instrument does not contain any modules that can be repaired by the user. If a malfunction occurs, please contact Thorlabs 
Technical Support and arrangements  will be made to investigate  the problem. Do not remove the cover. There are no user 
serviceable components inside. 

Optical patch cords used to connect to the front panel of the instrument should have their end faces cleaned every time a new 
connection is made. The end faces of the internal fiber connectors can easily be damaged by the use of dirty fiber ends. If 
damage occurs, the instrument will need to be sent back for repair. We suggest using a fiber end-face cleaning product such as 
the Thorlabs FCC-7020 shown below. Alternatively, a lint-free cloth moistened with isopropyl alcohol or methanol can be used. 
Never use acetone. 

 

The optical connectors on the front panel may be cleaned using a 2.5 mm bulkhead cleaner such as the Thorlabs FBC1. This 
allows the user to clean the fiber end-face without removing it from the internal bulkhead adapter. 

 

8.2  Replacement Parts 

The following parts can be obtained by contacting Thorlabs Technical Support 

 

SMA 50 Ω Loads (Used for Front Panel RF Connectors) 

 

PM Loopback Fiber Patch Cord for Front Panel 

 

Laser Interlock Keys for Front Panel Switch 

 

2.5 mm Interlock Pin (for Back Panel) 

 

1.25 A 250 VAC Fuse for Main Power 

 

Instrument IEC Main Power Cord 

 

Instrument Flip Foot

 

 

 

Thorlabs FCC-7020 

Fiber End-Face Cleaner for Patch Cords 

Thorlabs FBC1 

Fiber End-Face Cleaner for Bulkheads 

Содержание MX40G Series













































Отзывы: