THORLABS ITC1 Series Скачать руководство пользователя страница 33

Страница: 33 / 46

7 Maintenance and Service

7 Maintenance and Service

Protect the ITC1xx from adverse weather conditions. The ITC1xx is not water resistant.

Attention

To avoid damage to the instrument, do not expose it to spray, liquids or solvents!

The unit does not need a regular maintenance by the user. It does not contain any modules
and/or components that could be repaired by the user himself. If a malfunction occurs, please
check first the section

Troubleshooting

prior to contact Thorlabs GmbH for return instructions.

7.1 Troubleshooting

Unit does not work at all (no display)

Is the controller connected properly to the external power supply?

Connect the ITC1xx to a stable DC power supply with an output voltage (±12 to ± 15
V) and make sure, it is switched on.

You don’t get the desired laser output power

Is the interlock closed?

Check the resistance between the

interlock pins

of the connector jack - it must not

exceed 430

Is the laser output turned on?

Apply a logical "high" level to pin C15 of ST1 to turn on the laser output. The LED1a
on the controller board must light up.

The hardware limit I

LIM

might be set to 0.

Adjust the hardware limit I

LIM

using P1 to the desired value (

pin C20 of ST1

)

Is the laser diode installed properly?

Check the connection cables.

Is the switch S2 set according to the laser diode polarity?

Verify correct polarity and set S2 accordingly.

Is the photo diode connected properly?

Check the connecting cable.

Are you using a bias voltage with the photo diode in photo current mode?

Turn off bias voltage by interrupting the wiring bridge or change the polarity of the di-
ode for photo element mode (refer to section

Connecting Laser Diode and Photo Di-

ode

)

Is the desired output power adjusted correctly?

Set the ITC1xx to constant power mode (S1) and adjust the desired output power
P

, using P2.

Is the ITC1xx running in temperature protection mode?

Check if the temperature window is set correctly.

Check if the laser temperature is out of window (laser is then switched off automati-
cally).

Содержание ITC1 Series














































Результаты поиска

Содержание ITC1 Series

Отзывы:

Бренды по названию

Популярные бренды

THORLABS ITC1 Series, Руководство по эксплуатации

Результаты поиска

Содержание ITC1 Series

Отзывы:

Бренды по названию

Популярные бренды