4
4). INDOOR SIREN
This indoor siren emits a loud noise in the event of intrusion into your home.
Installation
/($
51
&76
21
9
-
/($
51
&76
21
9
/($51
&76
21
9
/($
51
&76
21
9
-
/($
51
&76
21
9
/($51
&76
21
9
ø8mm
To activate the indoor siren, connect the battery wires to the '3.6V' connector
on the siren's electronic card. The detector beeps briefly.
WARNING: For proper operation, the included indoor siren should be attached
to the wall or if not, temporarily placed on a flat surface (due to the anti-tamper
detector on the back).
/($
51
&76
21
9
anti-tamper device
/($
51
&76
21
9
- Warning: we recommend that you temporarily disconnect the loudspeaker
siren connector before moving it to its permanent position in order to avoid
inadvertently setting off the tampering alarm.
- Once mounted to the wall, ensure that the anti-tampering contact is in
contact with the wall and reconnect the loudspeaker connector, then replace
the cover of your indoor siren by tightening the screws and then replacing the
cover.
5). SMOKE DETECTOR
- For optimum protection, install a detector in each room.
- For minimum protection install one detector per floor, preferably in corridors
and stairwells.
- Switch on the smoke detector alarm (see TEST mode) in its final location and
check that you can hear it in every bedroom with the door shut and a radio on.
- The volume of the radio should be set to a level corresponding to a relatively
loud conversation. If you cannot hear the it due to the radio, it is highly likely
that your alarm would not be loud enough to wake someone who is asleep.
&XLVLQH
6pMRXU
&KDPEUH
&KDPEUH
&KDPEUH
FLAT
6DOOHjPDQJHU
&XLVLQH
6DOOHjPDQJHU
*DUDJH
%XDQGHULH
&RXORLU
(VFDOLHU
&KDPEUH
&KDPEUH
&KDPEUH
5G&
eWDJH
DETATCHED HOUSE
6DOOHjPDQJHU
&XLVLQH
6DOOHjPDQJHU
*DUDJH
%XDQGHULH
&RXORLU
(VFDOLHU
&KDPEUH
&KDPEUH
&KDPEUH
5G&
eWDJH
Minimum protection recommended
Optimum protection
Precautions for positioning
Rules for installation
- Install the smoke detector as near to the centre of the ceiling as possible
(best configuration).
- Install the smoke detector high against the wall with a distance of between
10 cm and 30 cm from the ceiling (acceptable configuration).
- In rooms with sloping ceilings, install the detector on one of the sloping sides
of the roof between 10 cm and 100 cm from the highest point.
>10 cm
>10 cm
<30 cm
>10 cm
In general, to avoid false alarms, smoke detectors should not be installed:
- In the garage (combustion residues are present when the car is started).
- In the kitchen (smoke generated by hobs, oven, etc.).
- In front of heating installations or in front of a ceiling fan and other areas with
strong currents of air.
- In very humid areas or in bathrooms with a bath or a shower. The steam and
humidity may cause false alarms.
- In dusty areas. Dust particles may cause false alarms or prevent the smoke
detector from triggering.
To activate the stand-alone smoke detector alarm:
- Remove the tab which protects the detector's battery (if the has already been
removed, replace the tab and remove it again), the detector should emit a
series of beeps.
- Firmly press the TEST button for 2 seconds, the detector should emit a series
of beeps.
- You may now place the detector in its permanent position.
Settings
- To test the smoke detector, press the button located on the cover of the
detector.
- The indicator flashes red as soon as the button is pressed and the alarm is
triggered if the electronic circuit, the siren and the battery are functioning.
- If the alarm is not triggered, this means the battery or another component are
faulty.
- THE SMOKE DETECTOR MUST BE TESTED ONCE A MONTH TO
ENSURE OPTIMUM OPERATION.
- A random or weak alarm noise coming from the detector may indicate the
product is faulty. In this case, stop using it.
E. PAIRING THE IP CAMERA WITH THE THOMBOX
Your camera allows you to take photos via the Thombox when movement is
detected. Photos are stored in the Thombox's 'Cameras' section, and the live
feed from the camera is also accessible from this same section.
Installation
The camera connects to your wired or wireless (WiFi) network. To set up the
camera, a wired connection is required (even if you will later decide to use a
wireless connection).
Reset
Power
Wireless
WPS
camera
Mains adapter
Modem/router connected to the
internet
You can now install your camera:
Make sure the camera is properly secured to prevent it from falling.
Lounge
dining room
dining room
Stairs
Corridor
Kitchen
Kitchen
Washroom
Bedroom
Bedroom
Bedroom
Bedroom
Bedroom
Bedroom
Ground
floor
Floor
