THOMSON ST 2030 SIP Скачать руководство пользователя страница 299

Страница: 299 / 316

ST2030s VoIP Business Phone

ST2030s SIP Administrator Guide v3.0

Page 291 of 308

Part 12 Troubleshooting

If your phone is not operating as it should, please refer to the list of the problems in the following
table. It should help you to solve the issue.

Problem

Possible cause

Remedy

No dialing tone

No connection to the
LAN

Ensure that the Ethernet cable is
correctly connected to the LAN
port and the hub.

No display

No power.

Ensure that the power supply is
correctly plugged in.

"Waiting for
CA…"
Message and no
dialing tone

One of the following
parameters is not set
correctly:
- Phone IP address
- Call agent (CA) address
- Subnet mask
- Gateway address

Check these parameters with
your system administrator.

Your call partner
cannot hear you
OR
You cannot hear
him.

The handset cable is not
correctly plugged in.

Ensure that the handset cable is
correctly plugged into the
handset and the telephone

Time is not the
one you’ve
programmed.

Time is automatically
specified
by the network.

Ask your system administrator.

"Phone needs to
be rebooted"
message.

Following changes in the
configuration of the
phone, a reboot is
needed to take effect.

Press the "OK" key to reboot the
phone.

Phone does not
always ring.

Call forwarding active or
Do not disturb facility set.

Read the relevant section of the
user guide. Deactivate the Call
forward function by pressing

Fwd

and “enable”

LED is blinking

Incorrect Network
connection

Unplug the Ethernet port and re-
plug it.

Table 9.1

Troubleshooting

Содержание ST 2030 SIP





























































































































































































































































































































Результаты поиска

Содержание ST 2030 SIP

Отзывы:

Похожие инструкции для ST 2030 SIP

Бренды по названию

Популярные бренды

THOMSON ST 2030 SIP, Руководство администратора

Результаты поиска

Содержание ST 2030 SIP

Отзывы:

Похожие инструкции для ST 2030 SIP

Бренды по названию

Популярные бренды