THOMSON ST 2030 SIP Скачать руководство пользователя страница 219

Страница: 219 / 316

ST2030s VoIP Business Phone

ST2030s SIP Administrator Guide v3.0

Page 211 of 308

Trusted IP for Notify “check-sync”

Up to now it was possible to send a SIP NOTIFY message to the phone, to

launch remotely the automatic provisioning.
Extract of the APS document "ST2030-ST2022 AutoProvisioning-V0030.doc" :

To avoid attacks once the feature is enabled (as mentioned above), an
additional parameter has been created to contain the authorized server from

which the Notify is going to be allowed.
NOTIFY messages with event=check-sync, coming from other servers are

ignored.
To minimize the impact of such attacks, the phone will not send any

response.

The default value will be 0.0.0.0, which means the phone will accept all

NOTIFY (check-sync) messages coming from everywhere.
This parameter shall be either an IP address or a domain name.

Remember that the proper APS pre-configuration should be:

[sip]
sw_notify_autoprovision=

AuthNotifyCheckSync=

10.0.0.1

[autoprovision]
AutoprovisionFlag=

AutoprovisionTFTPServer=

10.0.0.1

AutoprovisionConfigname=

ST2030S.inf

Содержание ST 2030 SIP





























































































































































































































































































































Результаты поиска

Содержание ST 2030 SIP

Отзывы:

Похожие инструкции для ST 2030 SIP

Бренды по названию

Популярные бренды

THOMSON ST 2030 SIP, Руководство администратора

Результаты поиска

Содержание ST 2030 SIP

Отзывы:

Похожие инструкции для ST 2030 SIP

Бренды по названию

Популярные бренды