THOMSON 510062 Скачать руководство пользователя страница 56

Страница: 56 / 64

MOTOR DRIVE FOR 2-PANEL GATES - CONNECT

www.mythomson.com

F - MAINTENANCE AND UPKEEP

2. OPERATING INDICATORS

This system has two operating indicators: the battery charge level (optional) and the history of events.

Charge batterie

PROG

Code 1

PROG

–

Code 2

Code 3

–

Code 4

–

OK 3s

efface historique

du plus

récent

au plus

ancien

(dernière

erreur

)

historique des événements

2.1. History of events and error codes

• During operation, events may occur that may be malfunctions of the motor drive or consequences of

user actions.

• Each event has a different code.
• This code is displayed by a combination of red LEDs that are on, off or flashing on the

MENU 0

display.

• When

PROG

are pressed, this code is deleted. However, the last 4 codes generated are

memorised, and can be viewed in a history.

• To access them, press

twice, then use the “

” and “–” buttons to scroll through the memorised

codes.

To diagnose any problems, here is the list of codes and their meaning:

: LED off
: LED on
: Flashing LED light

There are two types of code:

Error (E) or Information (I)

. N.B. an error requires action from the

installer to correct the motor drive problem.

MEANING

TYPE

An obstacle has been detected in M1 when closing.

An obstacle has been detected in M2 when closing.

The photocell beam has been obstructed.

An obstacle has been detected in M1 when opening.

Содержание 510062

































































Результаты поиска

Содержание 510062

Отзывы:

Похожие инструкции для 510062

Бренды по названию

Популярные бренды

THOMSON 510062, Руководство по подключению

Результаты поиска

Содержание 510062

Отзывы:

Похожие инструкции для 510062

Бренды по названию

Популярные бренды