A
.5
V
E
L
-3
3
Optical Fibers (up to 1000 meters)
available with ST-, SC- or LC-type
connectors
100-240V -, 0.5A, 50/60 Hz
T2A, 250 VAC
CAUTION!
Replace with same type and rating fuse.
L1
L2
DVI 1 OUT
DDC MODE
LCL REM
ACQUIRE
SELECT
DDC MODE
LCL REM
ACQUIRE
SELECT
DDC MODE
LCL REM
ACQUIRE
SELECT
L3
L4
L5
L6
DVI 1 IN
DVI 2 OUT
DVI 2 IN
DVI 3 OUT
DVI 3 IN
PWR
100-240V -, 0.5A, 50/60 Hz
T2A, 250 VAC
CAUTION!
Replace with same type and rating fuse.
L2
L1
DVI 1 OUT 1
DDC
DDC MODE
LCL REM
ACQUIRE
SELECT
DDC MODE
LCL REM
ACQUIRE
SELECT
DDC MODE
LCL REM
ACQUIRE
SELECT
L4
L3
L6
L5
DVI 1 OUT 2
DVI 2 OUT 1
DDC
DVI 2 OUT 2
DVI 3 OUT 1
DDC
DVI 3 OUT 2
PWR
L1/L2
L3/L4
L5/L6
L2/L1
L4/L3
L6/L5
Copyright
©
2013. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
DVI 1 IN
DVI 2 IN
DVI 3 IN
DVI 1 OUT 1 & 2
DVI 2 OUT 1 & 2
DVI 3 OUT 1 & 2
DVI 1 OUT
DVI 2 OUT
DVI 3 OUT
STEP 3:
Using standard
DVI-D cables, connect the
desired video output
devices to the Receiver
Unit’s DVI OUT receptacles.
For each of the three video
output pairs, DVI OUT 1 is
the DDC port.
STEP 2:
Ensure that the Power Switch is
in the OFF (0) position. Connect the
supplied AC Power Cord (PWR-000006-R)
to the Receiver’s power receptacle, plug it
into a standard AC source and turn the
unit ON (1).
STEP 1:
Connect the multi-
mode fiber optic cables
between the Tx and Rx
Units (up to 1000 meters).
Do not kink or pinch the
cables and be sure to keep
all bend radii to no less than
3 inches.
STEP 5:
Using the
supplied DVI-D male to
male cables, connect
the desired video output
devices to the
Transmitter Unit’s DVI
OUT receptacles.
STEP 6:
Using the
supplied DVI-D male to
male cables, connect the
video output sources to
the Transmitter Unit’s DVI
IN receptacles.
Ensure
that all system functions
are operating properly
.
CPU 1
CPU 2
CPU 3
STEP 4:
Ensure that the
Power Switch is in the OFF
(0) position. Connect the
supplied AC Power Cord
(PWR-000006-R) to the
Transmitter’s power
receptacle, plug it into a
standard AC source and
turn the unit ON (1).
Digital Video Extension System - 33
MRTS
Technology
Transmitter
Powered by
STATUS
STATUS
STATUS
Tx STATUS LEDs
GREEN:
Fibers connected, good link
established.
ORANGE:
Local Status Mode selected, no
fiber link from Rx to Tx, or both DDC Mode
buttons held down (waiting to reload
default DDC table).
RED flashing:
No fiber link from Rx to Tx.
Rx STATUS LEDs
GREEN:
DVI monitor has good link to primary DVI
OUT port (labeled DDC).
ORANGE:
No DVI monitor connected to primary port
RED flashing:
No fiber link from Tx to Rx.
TRANSMITTER
RECEIVER
QUICK START GUIDE
Digital Video Extension System -
33
The Primary Port on the Rx is used for DDC.
The Secondary Port carries video data only.
VELOCITY-33_Manual_Quick_Start_Rev_C
U
S
E
O
N
L
Y
W
IT
H
2
5
0
V
F
U
S
E
U
S
E
O
N
L
Y
W
IT
H
2
5
0
V
F
U
S
E
1
2
1
2
1
2
1
2
3
6
5
4
1
2
3
