background image

Rear Panel Layout 

 

 

 
 

Figure 4 – Rear Panel Layout showing both single and two channel modules installed 

 

1. Channel 

THERMAL

 

LED

.  Illuminates when the channel rises above the maximum operating temperature. The 

Dreadnaught II should be powered off and cooled when this LED is lit. 

 

2. Channel 

RAIL FUSE +

 

LED

.  When this LED is illuminated, the fuse on the positive rail of the channel is blown. 

(Internal on 2 channel modules). 

 

3. 

Module

 RAIL FUSE

.  If necessary to replace, use only same type and rating. 

 

4. 

BINDING POST

.  (Single Channel module).  Connect plus and minus speaker wires for one speaker to 

appropriately marked terminals of each post.  The binding post on the single channel module will operate 
optimally using spade lugs.

 

 

5. Channel 

RAIL FUSE LED

. When this LED is illuminated, an internal fuse on the negative rail of the channel is 

blown.  (Internal on 2 channel modules).

 

 

6. 

SINGLE-ENDED 

input jack on single channel module.

 

 

7. 

STEREO/SURROUND

 buss selector switch.  Assigns the module to either the 

STEREO

 or 

SURROUND

 buss. 

 

8. 

-

 Module

 RAIL FUSE

.  If necessary to replace, use only same type and rating. 

 

9. 

BALANCED

 input jack on single channel module. 

 

10. 

POSITIVE BINDING POST

 – Channel A.  (Two channel module).  Connects to the +  (plus) speaker connector.  

The binding posts on the two channel module can accept spade lugs, banana plugs or bare wire. 

 

11. 

NEGATIVE BINDING POST

 – Channel A.  (Two channel module).  Connects to the – (minus) speaker connector. 

 

12. 

BALANCED

 input jack – Channel A of two channel module. 

 

13. 

SINGLE-ENDED 

input jack – Channel A on two channel module. 

 

14. 

POSITIVE BINDING POST

 – Channel B.  (Two channel module).  Connects to the +  (plus) speaker connector.  

The binding posts on the two channel module can accept spade lugs, banana plugs or bare wire. 

 

15. 

NEGATIVE BINDING POST

 – Channel B.  (Two channel module).  Connects to the – (minus) speaker connector. 

 

16. 

STEREO/SURROUND

 bus selector switch.  Assigns the affected module (both channels) to either the 

STEREO

 

or 

SURROUND

 buss. 

 

 

7

Содержание Dreadnaught II



























Отзывы: