Thern FVC-1000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

Thern FVC-1000 Скачать руководство пользователя страница 9

Owner's Manual for Thern Model FVC-1000 Winches

page 9

A8018B-1210

2.3.7

DISENGAGE THE RATCHET by moving the ratchet spring to the
RATCHET DISENGAGED position and turning the handle clockwise
slowly until the ratchet disengages completely.

If you feel pressure in the

handle, do not let it go. Do not let go of the handle until the fi re vent is
held securely by the band brake.

2.3.8

READJUST BRAKE TENSION as necessary by repeating the above steps
until the fi re vent is held securely closed.

Always engage the ratchet before

adjusting the band brake.

2.3.9

REMOVE THE HANDLE and slide it into the slot in the guard for storage.

Make sure the ratchet is in the RATCHET DISENGAGED position.

2.4

Testing the Fire Vent

Remove the handle before testing fi re vent operation. The handle will spin if
attached to the winch.

Keep away from the spinning drum and input shaft when fi re vent is released
during testing.

2.4.1

MAKE SURE THE HANDLE is removed from the winch or stored in the
guard frame.

2.4.2

MAKE SURE THE RATCHET is in the RATCHET DISENGAGED posi-
tion.

2.4.3

OPEN THE ACCESS PANEL on the back of the winch by removing the
lynch pin and pulling the panel down.

2.4.4

RELEASE THE FIRE VENT by standing clear of the winch and pulling
down on the test handle to release tension in the band brake.

Keep away

from the spinning drum and input shaft during the test operation.

2.4.5

VERIFY THE FIRE VENT OPENS FULLY when the test arm is pushed
down and the brake is released. If the fi re vent fails to open, engage the ratch-
et and loosen the band brake by turning the adjusting nut counterclockwise
1/4 turn. Continue to adjust the brake until the fi re vent springs open properly
when the brake is released with the test arm.

2.4.6

RESET THE FIRE VENT by following the instructions to CLOSE and SET
the fi re vent.

«
...
7
8
9
10
11
...
»

Содержание FVC-1000

























Отзывы:

Нет отзывов