THERMOROSSI DORICA MAIOLICA, Инструкция по установке, эксплуатации и обслуживанию

Страница: 22 / 56

Page 22
e manutenzione
It is possible to carry out the weekly programming by setting up to 3 on/off cycles for each day from Monday to Sunday. To program
the appliance press button (6) twice until the word CRONO appears followed by the words illustrated in the figure above on the left.
Now you can begin programming the first day of the week - Monday - by pressing button (1). Press the arrow button (3) and/or (4)
to choose another day to be programmed, to confirm the selection press button (1) again. The words ON1 will appear on the display
followed by 2 blinking digits indicating the hours (figure above right). Press button (3) and/or (4) to enter the hour of the first cycle
start time. To confirm the selection press the button (1). The 2 digits indicating the minutes will start flashing. Press button (3)
and/or (4)to enter the minutes of the first cycle start time. To confirm the selection press the button (1). The first start up time for the
selected day has now been set. Then the inscription OFF1 will appear in the display and the two digits representing the hours will
turn on. When the (3) and/or (4) button is pressed the hour of the first off-cycle is entered.
To confirm the selection press the button (1). The 2 digits indicating the minutes will start flashing. By pressing the button (3) and/or
(4) the minutes for the first off-cycle will be entered. To confirm the selection press the button (1). This concludes the setting of the
first on-off cycle for the selected day. Later, it is possible to set the second on-off cycle (e.g. Monday) (shown with the display of
ON2 and OFF2) and the third Monday’s on-off cycle (shown with the display ON3 and OFF3). Next the display appears as
illustrated in the figure above on the left. Press the arrow button (3) and/or (4) to choose another day to be programmed, to confirm
the selection press button (1) again.
If you wish to copy all the on-off programs, for example the Monday settings, to the other days of the week, proceed as follows:
press button (6) until the word "CRONO" appears followed by the screen illustrated in the figure below on the left. Next press button
(2) and the display appears as illustrated in the figure below on the right: the program for Monday has been copied to Tuesday.
Press button (2) again to copy the program to Wednesday, Thursday ...
. In the programming menu if you wish, for example, to edit the programming for Sunday press button (3) and/or (4) to go to
Sunday and then press button (1). If the second on-off cycle is not required simply set the ON2 time as 00:00 and the OFF2 time as
00:00 .
The programming procedure ends when you confirm the last data entered by pressing button (6) or when you exit the programming
menu. During the START, WORK or OFF phases press button (5) to enable / disable the programming (Enabled = CR.ON appears
momentarily on the display together with the fixed presence of the chrono symbol on the right of the display (see figure below).
Disabled: message CR.OFF temporarily displayed and, at the same time, the chrono symbol on the right side of the display is not
present (see figure below): this function is useful if you wish to disable the established weekly program setting. Moreover, you can
reset, or delete, all the programmings by holding down (in OFF or START or WORK phase) button (5) for approximately 8 seconds;
the word "RESET CRONO" appears momentarily in order to indicate deletion of all the programmings previously set. With the
programming active, the operating conditions at the start-up (combustion power – ventilation speed) are the same as set-up before
the last off-cycle of the appliance: this is the case if the off-cycle has been done through the programming and not through a manual
action.
Manual shut down can only be carried out with the programming disabled. After shut down, by re-enabling the programming, at the
next start up controlled by the programming the appliance will be set at the first combustion power position and first ventilation
speed.
In the event of a programmed cycle on always ensure that the brazier is clean and seated correctly in its
lodging: failure to clean the brazier can reduce and/or affect the life of the spark plug as it would be
subjected to high temperatures due to poor cooling. When the programming is enabled (CR.ON appears
momentarily together with the fixed presence of the chrono symbol on the bottom of the display) any
additional chronothermostats (see para. 7.2) are disabled.
DAYS
CRONO MON
3
4
8
2
5 7
6
1
DAYS
CRONO TUE Copy
3
4
8
2
5 7
6
1