USING THE PANEL HEATER
1) Description of the control unit :
r
u
➔
Mode switch knob.
v
➔
ECO temperature set value adjustment knob.
w
➔
COMFORT temperature set value adjustment knob.
V1
➔
Heating light.
V2
➔
ECO mode light.
V3
➔
COMFORT light.
2) Fixing the comfort temperature :
The comfort temperature that you would like while the room is occupied.
a) Set the cursor
u
to
,
the heating light
V3
comes on.
b) Set the control knob
w
to 5, the heating light
V1
comes on, if the room temperature is below the required temperature.
c) Wait a few hours until the temperature stabilizes.
d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position.
If the setting is not satisfactory, adjust it and start again from point c.
3) Fixing the Eco temperature :
This is the required temperature during periods when the room is unoccupied.
It is recommended that this mode should be used if the room is unoccupied for more than 2 hours.
a) Set the cursor
u
switch knob to
,
the heating light
V2
comes on.
b) Adjust the control knob
v
between 3 and 4, the heating light
V1
comes on, if the ambient temperature is lower than
the instruction of desired Eco temperature.
c) Wait a few hours until the temperature stabilizes.
d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position.
If the setting is not satisfactory, adjust it and start again from point c.
4) Frost-Free mode :
This mode is used to keep the temperature at approximately 7°C in the room when you are absent from the house for
a prolonged period (i.e. more than 24 hours).
a) Set the cursor
u
to
.
5) The heating indicator : V1
This light indicates periods during which the element is heating. It flashes when the temperature is stable, and it goes
off if the temperature is too high.
6) Switching off the device :
To set the device to the Off position, move the cursor to .
7) Locking the controls :
s
It is possible to lock or limit the range of use of thumb-wheels
v
and
w
and lock selector switch cursor
u
to prevent
the inadvertent manipulation of the device (by children, etc).
a) Detach the device from its wall bracket.
b) On the back of the thermostat box, detach pins
P
from their supports.
c) Choose position
B
to lock the thumb-wheels or position
L
to limit the range of use of the thumb-wheels.
Choose one of the positions
M
to lock the person in the desired mode.
s
d
n
a
m
m
o
C
d
e
v
i
e
c
e
R
t
n
e
r
r
u
c
o
N
o
n
n
o
i
t
a
n
r
e
t
l
A
)
''
7
5
'
4
(
t
n
e
r
r
u
c
)
''
3
(
V
0
3
2
e
s
a
h
p
o
n
n
o
i
t
a
n
r
e
t
l
A
)
''
3
5
'
4
(
t
n
e
r
r
u
c
)
''
7
(
V
0
3
2
e
s
a
h
p
e
t
e
l
p
m
o
C
V
0
3
2
n
o
i
t
a
n
r
e
t
l
a
-
f
l
a
h
e
v
i
t
a
g
e
N
V
5
1
1
-
n
o
i
t
a
n
r
e
t
l
a
-
f
l
a
h
e
v
i
t
i
s
o
P
V
5
1
1
+
n
o
i
t
a
n
r
e
t
l
a
e
p
o
c
s
o
ll
i
c
s
O
l
a
r
t
u
e
N
/
f
é
R
e
d
o
M
d
e
n
i
a
t
b
o
t
r
o
f
m
o
C
C
°
1
-
t
r
o
f
m
o
C
C
°
2
-
t
r
o
f
m
o
C
o
c
E
e
z
e
e
r
f
-
i
t
n
A
p
o
t
S
t
u
C
r
e
w
o
P
Table of commands the panel heater can receive on its pilot wire. To be measured between the pilot wire and the neutral.
080214_CEETvariation_ang.PMD
07/09/05, 14:06
2