Thermolec DCC-10 series Скачать руководство пользователя страница 4

Страница: 4 / 17

safety information

this document describes important safety instructions which must be
followed during installation, maintenance and application of the dcc –
charge controller for electric vehicle.

warning

Read all instructions prior using this
product.
always disconnect the dCC – Charge
controller for electric vehicle power sup-
ply before any works.
use only the dCC – Charge controller for
electric vehicle by following the technical
specifications indicated in this installation
manual.
do not install the dCC – Charge controller
for electric vehicle nearby inflammable
materials, explosives or fuels, chemical
products and vapors.
do not install the dCC – Charge controller
for electric vehicle outdoor.
never spray the dCC – Charge controller
for electric vehicle with water or any other
liquids.
dCC – Charge controller for electric
vehicle stop using the dCC – Charge
controller for electric vehicle immediately
if defective, cracked, broken or damaged.
never try to modify, repair or dismantle
the dCC – Charge controller for electric
vehicle. Please contact the manufacturer
for any malfunction.
never insert a sharp object inside the
dCC – Charge controller for electric vehi-
cle at the risk of causing damages to the
components.
any improper use of the dCC – Charge
controller for electric vehicle could result
in serious injuries which may cause
death.
For a vertical installation on a wall, refer
to the information’s on the enclosure for
the choice of mounting position.

precautions

any improper use of the dCC – Charge
controller for electric vehicle can cause
damages and premature wear of the com-
ponents, which voids the warranty.
never use the dCC – Charge controller
for electric vehicle above or below the
temperature range of 32 °F to 113 °F (0
°C to 45 °C).
the installation of the dCC – Charge
controller for electric vehicle must be
done in accordance with the latest electri-
cal code requirements.

notes

It is recommended to schedule the char-
ging of the vehicle during hours of low
electrical consumption to minimize inter-
ruptions to the electric charging station.
always check that the dCC – Charge
controller for electric vehicle is adequa-
tely fixed to the wall or ceiling or in a loca-
tion to avoid any damages.
It is the installer’s responsibility to make
sure that the electric power source is
adequate for the use of one or more dCC.
do not use any cleaning solvents to clean
the dCC – Charge controller for electric
vehicle.

limited warranty

1 -

tHermoleC ltÉe.

warrants the inte-

grated controls against any defects for a
period of one year from the shipping date.
the warranty is limited to the equipment
and components supplier by

tHermoleC

ltÉe.

2 – In case of incorrect installation, inap-
propriate use or repairs done by unautho-

rized personnel by

tHermoleC ltÉe.

the warranty will be automatically void.
3 -

tHermoleC ltÉe.

undertakes to

repair or replace, at site or at the manu-
facturing location, at his option, the
defective material only after an evaluation
made by its representative.
4 -

tHermoleC ltÉe.

will not be held

liable for damages or delays and will not
be required to pay transport cost of the
charge controller said to be defective.
5 -

tHermoleC ltÉe.

shall not be liable

for any indirect damages or delays caused
by faulty workmanship or materials.
no indemnity will be paid for repairs,
replacements or modifications without a
prior written consent supplied by

tHer-

moleC ltÉe.

6 – any control device or accessory sup-
plied with the dCC – Charge controller for
electric vehicle to be installed or connec-
ted remotely from the charge controller
will be guaranteed by the manufacturer
only under the special conditions mentio-
ned in paragraph 5.
7 – the components supplied for repairs
are guaranteed for the remaining of the
warranty on the original product or 90
days. the longest period will prevail.
8 – all repairs made at the

tHermoleC

ltÉe.

plant are guaranteed for 30 days

from the date of repairs.

specifications

the dcc – charge controller for electric vehicle is a safety device with
programmable controller that can protect an electrical distribution
circuit in relation with its main breaker. it will prevent overloading the
electrical distribution circuit by turning off momentarily the power to
the charging station when the demand exceeds 80% of the main brea-
ker rating.

models

Breaker

main power supply

eV charger 60a 70a 80a 90a 100a 125a 150a 200a

dcc-10-30a 30a

✓

dcc-10-40a 40a

✗

✓

dcc-10-50a 50a

✗

✓