Thermofilm HEATSTRIP THN2000 Скачать руководство пользователя страница 9

 

 

 

MOUNTING

 

 

Fix the two mounting brackets to the ceiling or wall in the desired location (refer minimum bracket centre chart). Make sure 
the method of fixing (bolts or screws) will be more than strong enough to support the weight of the heater, allowing for 
strong winds and other conditions.

 

 

• 

Slide the 2 locking brackets into the groove on the back of the heater. Make sure the pins on the locking bracket are 
facing the matching holes in the top mounting bracket.

 

• 

Lift heater into position and secure the 2 locking brackets to the mounting brackets using the screws provided. Make 
sure the 2 pins on the locking bracket engage with the matching holes in the mounting bracket. The pins will allow for 
both horizontal or angle mounting as required

 

• 

Tighten  all  screws  and  tighten  the  round nut at  the top  of the  bracket,  so  it  locks onto  the  top  part of  the mounting 
bracket.

 

 

NOTE: The standard bracket allows for normal or angle mounting of the heater and is suitable for ceiling or wall mounting.

 

MODEL

 

B

 

MINIMUM DISTANCE (mm)

 

THN2000

 

490

 

Left: 

Suspension mounting using the standard 

mounting brackets

 

 

NOTE: Chains or wire not included

 

Содержание HEATSTRIP THN2000













Отзывы: