Thermo Scientific Surveyor UV Plus Скачать руководство пользователя страница 49

Страница: 49 / 76

Maintenance

Standard Analytical Flow Cell

Thermo Scientific

Surveyor UV/Vis Plus Detector Hardware Manual

Standard Analytical Flow Cell

To remove or install the standard analytical flow cell, follow these topics:

•

Removing the Standard Analytical Flow Cell Assembly

•

Installing the Standard Analytical Flow Cell

Removing the Standard Analytical Flow Cell Assembly

To clean or replace the standard analytical flow cell, remove it from the UV/Vis detector.



To remove the standard analytical flow cell

1. Turn the detector off and unplug the detector from line power.

2. Open the front doors of the detector.

The flow cell assembly is located behind the flow cell cover.

3. Remove the flow cell cover by unscrewing the flow cell cover retention screw and pulling

it straight out and away from the flow cell assembly. See

Figure 25

Figure 25.

Surveyor UV/Vis Plus Detector with the flow cell cover installed

CAUTION

Flow cells are factory-assembled units. Do not disassemble them.

CAUTION

To prevent possible exposure to UV light, turn the detector off and unplug

the power cord from the power receptacle on the back panel.

Standard analytical flow cell
cover retention screw

Содержание Surveyor UV Plus













































































Результаты поиска

Содержание Surveyor UV Plus

Отзывы:

Похожие инструкции для Surveyor UV Plus

Бренды по названию

Популярные бренды

Thermo Scientific Surveyor UV Plus, Руководство по оборудованию

Результаты поиска

Содержание Surveyor UV Plus

Отзывы:

Похожие инструкции для Surveyor UV Plus

Бренды по названию

Популярные бренды