Thermo Scientific Smart2Pure Pro Скачать руководство пользователя страница 49

Страница: 49 / 57

44 | Troubleshooting

Smart2Pure Pro Ultrapure water system

Troubleshooting

Note:

Contact the service department if you cannot rectify this error.

Error

Cause

Solution

The system does not start

No supply of power

Power pack or system control defect

Power Switched OFF

Provide power

Replace the power pack or system control

Press power ON switch on the display

Dispensing not possible/
storage tank is empty

Feed-water supply is closed

Feed-water and concentrate water
connections are mixed up

Feed-water pressure <2 bar

Sterile filter blocked

RO cartridge blocked.

Open the feed-water supply line

Replace connections

Increase feed-water pressure

Replace the sterile filter (refer to the section

Replacing the 0.1 μm Final Filter

)

Install new RO cartridge (refer to the section

Replacing the RO Cartridge

or check RO

cartridge connections

Resistance <18.2 MΩ·cm /
0.055 μS/cm

Ultrapure cartridge is exhausted

Air in the ultrafilter because of empty
tank

Check feed-water quality

Insert new ultrapure cartridge

Wait until the tank is again filled and a rinse is
triggered

Control panel non
responsive

Storage tank’s water level is below
25% and tank filling is in progress,

Microprocessor locked up error

Normal operation. All function keys on the display
are

DISABLED

while system is filling to

0 - 25%. Wait until storage tank has filled to 25%
level.

If control panel is non responsive and tank level is
>25%, unplug the mains plug for 5 seconds.

Contact the Thermo Fisher Scientific service
department

System leak

Error message:

“System Leak Detected/
Turn Feed-water OFF -
Contact Service”

Leak sensor in contact with water

Leaky tubing connection

Feed-water pressure >6 bar

Component defect (e.g. UV quartz
tube)

Unplug power supply.

Clean and dry leak detection sensor

Plug power supply and follow the control logic
procedure if a leak is detected. 40 second delay
in error allows time for detecting and correcting
leak. Repeat as necessary to correct leak

Check and seal the tubing connection

Install a pressure reducer

No leak detected, verify if high humidity
conditions in room. Turn off leak detection in
OEM menu for high humidity conditions”

Contact the Thermo Fisher Scientific service
department

Содержание Smart2Pure Pro


























































Результаты поиска

Содержание Smart2Pure Pro

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific Smart2Pure Pro, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Smart2Pure Pro

Отзывы:

Бренды по названию

Популярные бренды