Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 9 / 442

background image

Declaration

Manufacturer: Thermo Fisher Scientific

Thermo Fisher Scientific is the manufacturer of the instrument described in this manual and, as such, is responsible for
the instrument safety, reliability and performance only if:

• installation,

• recalibration, and

• changes and repairs

have been carried out by authorized personnel and if:

• the local installation complies with local law regulations,

• the instrument is used according to the instructions provided, and

• if its operation is only entrusted to qualified trained personnel.

Thermo Fisher Scientific is not liable for any damages derived from the non-compliance with the aforementioned
recommendations.

Regulatory Compliance

Thermo Fisher Scientific performs complete testing and evaluation of its products to ensure full compliance with
applicable domestic and international regulations. When the system is delivered to you, it meets all pertinent
electromagnetic compatibility (EMC) and safety standards as described in the next section or sections by product name.

Changes that you make to your system may void compliance with one or more of these EMC and safety standards.
Changes to your system include replacing a part or adding components, options, or peripherals not specifically
authorized and qualified by Thermo Fisher Scientific. To ensure continued compliance with EMC and safety standards,
replacement parts and additional components, options, and peripherals must be ordered from Thermo Fisher Scientific
or one of its authorized representatives.

EMC and Safety Standards

• ITQ, and Ion Trap Series standards: EMC: EN 61326-1:2006. Safety: IEC 61010-1:2001, IEC 61010-2-081:2001

• Direct Probe Controller (DPC) standards: EMC: EN 61326-1:2013. Safety: IEC 61010-1:2001,

IEC 61010-2-081:2001

• ISQ and ISQ 7000 standards: EMC: EN 61326-1:2013. Safety: IEC 61010-1:2010 (ed. 3); IEC 61010-2-

081:2015 (ed. 2); IEC 61010-2-010:2014 (ed. 3); IECEE CB SCHEME CERT NO. DE 3-30000

• TSQ 9000, TSQ 8000 Evo and TSQ Duo standards: EMC: EN 61326-1:2013. Safety: IEC 61010-1:2010 (ed. 3);

IEC 61010-2-081:2015 (ed. 2); IEC 61010-2-010:2014 (ed. 3); IECEE CB SCHEME CERT NO. DE 3-30034

«
...
7
8
9
10
11
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: Bacharach Страницы: 19

Бренд: Keithley Страницы: 55

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

Бренд: Saluki Страницы: 312

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: Magnescale Страницы: 36

Rainbow RTI-Nano Series

Бренд: Laserworld Страницы: 25

Бренд: Bartington Страницы: 32

Бренд: Alfano Страницы: 47

ENSEMBLE GRANDE MARK 5

Бренд: Kurzweil Страницы: 32

Бренд: Readiness Systems Страницы: 16

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

Бренд: Hanna Instruments Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды