Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 399 / 442

Advanced Maintenance

Replacing Fans and Filters

Thermo Scientific

ISQ 7000 Hardware Manual

371

Chassis Cooling Fan



To replace the chassis cooling fan

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

page 149

2. Use a T20 Torxhead screwdriver to loosen the screw at the top center of the interior front

panel. Then slide the top cover panel toward the back of the instrument and lift it off.

3. Remove the four rivets holding the finger guard in place.

4. Remove the four rivets holding the chassis cooling fan to the back panel of the

instrument.

5. Remove the chassis cooling fan.

6. Disconnect the fan from the distribution board on the bottom of the instrument.

7. Connect a new fan to the distribution board.

8. Reattach the four rivets holding the fan to the back panel of the instrument.

9. Reattach the four rivets holding the finger guard in place.

10. Reattach the top cover panel and tighten the screw holding it in place.

11. Restart your system by following the instructions in

“Restarting the System”

page 165

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering this

component.

Note

You do not have to remove the ion source cartridge or the column or vent the

instrument. If you are using hydrogen as a carrier gas, power off the GC.

Figure 422.

Removing the Chassis Cooling Fan

Rivets

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды