Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 193 / 442

background image

3

Advanced Maintenance

Replacing Components of the Analyzer

Thermo Scientific

ISQ 7000 Hardware Manual

165

10. Align the manifold door with the ion source and screw it to the manifold.

11. Install the CI and calibration tubes if they are not already installed.

a. Use 1/16 in. graphite-Vespel ferrules and tighten 1/2 turn past the position that just

begins to hold the tubing firm. Do not reuse graphite-Vespel ferrules more than three
times as they can become too compressed to re-tighten if a leak is found at their seal.

b. Replace the right side cover.

12. Install the column or no-hole ferrule.

13. Ensure the transfer line is positioned correctly in the GC oven.

14. Use the source plug and associated procedure to make sure column is placed at the edge of

the ion source.

15. Close the manifold door and reattach the four screws. Confirm that front door screws

hold door completely to the manifold.

16. Reconnect the four wires that connect the front 4-pin feedthrough to quadrupole 1 and

the ion guide.

17. Put the glass manifold covers back into place. Be sure to blow off all dust from the covers

and o-ring first.

18. Reconnect the electrometer board cable.

19. Reattach the top cover and tighten the top cover panel screw

Restarting the System

1. Replace the front door screws or reattach the manifold door and the four screws.

2. Close the front door of the instrument.

3. Twist the vent valve knob clockwise to close the valve. Be sure not to pinch the vent valve

o-ring.

4. Reinsert the column to the proper length and tighten the transfer line nut.

5. If you are using hydrogen as a carrier gas, replace the front panel screw.

6. Replace the ion source cartridge. Replace all remaining hydrogen safety screws if you are

using hydrogen.

CAUTION

Although the wires are insulated with glass braid, they may short through the

insulation if they touch a metal surface.

Note

For proper alignment and sensitivity, the front manifold door should be screwed

down fully to keep the magnet alignment with the ion source correct.

«
...
191
192
193
194
195
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: ECC X-RAY Страницы: 14

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Бренд: XS Scuba Страницы: 24

Бренд: Tactical Controls Страницы: 11

Бренд: FarmChem Страницы: 8

MIC TRAC MT-3000

Бренд: GAGEMAKER Страницы: 20

Бренд: A&D Страницы: 39

Бренд: Yamaha Страницы: 84

Бренд: Rabid Elephant Страницы: 18

Бренд: Keysight Страницы: 66

Бренд: JRC Страницы: 308

Бренд: Neogen Страницы: 9

Бренд: Raytech Страницы: 7

Бренд: X-Rite Страницы: 130

Бренд: Eno Scientific Страницы: 47

Бренд: YOKOGAWA Страницы: 104

Бренд: Suaoki Страницы: 79

Бренд: Banner Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды